Yamaha CD-N500 Owners Manual - Page 26

Setup menu list, Submenu, Settings, default, Function - firmware

Get Yamaha CD-N500 PDF manuals and user guides View all Yamaha CD-N500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

SETUP MENU Setup menu list Menu Submenu DHCP IP Address Network Configuration Subnet Mask Default Gateway DNS Server (P) DNS Server (S) Network Information MAC Address Status System ID Network Standby Auto Power Down Dimmer Firmware Version Firmware Update Settings (Bold: default) On, Off Function Select "On" to use the DHCP server to automatically configure the network settings of this unit or "Off" to configure manually. Specify the IP address when "DHCP" is "Off". *1 Specify the subnet mask when "DHCP" is "Off". *1 Specify the default gateway when "DHCP" is "Off". *1 Specify the primary DNS server when "DHCP" is "Off". *1 Specify the secondary DNS server when "DHCP" is "Off". *1 On, Off 4 Hours, 8 Hours, 12 Hours, Off -3 to 0 Network, USB The MAC address of this unit is shown. The MAC address is also used as a vTuner ID. The network status of this unit is shown ("Connected" or "Not connected"). The system ID number is shown. Select "On" to enable the network standby mode. This unit automatically enters standby mode if it is left turned on for the selected time without playback or any other operation being performed. Adjust the brightness of the front panel display. The firmware version of this unit is shown. Update the firmware of this unit after selecting "Network" or "USB". When "Press ENTER to start" appears, press ENTER to start firmware update. Do not operate this unit until "UPDATE SUCCESS" appears. Then turn off this unit once and turn it on again. *1: When "DHCP" is "On", you can check the values (IP address, etc.) assigned by the DHCP server. 24 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
SETUP MENU
24
En
*1: When “DHCP” is “On”, you can check the values (IP address, etc.) assigned by the DHCP server.
Setup menu list
Menu
Submenu
Settings
(Bold:
default)
Function
Network
Configuration
DHCP
On
, Off
Select “On” to use the DHCP server to automatically configure the
network settings of this unit or “Off” to configure manually.
IP Address
Specify the IP address when “DHCP” is “Off”.
*1
Subnet Mask
Specify the subnet mask when “DHCP” is “Off”.
*1
Default
Gateway
Specify the default gateway when “DHCP” is “Off”.
*1
DNS Server
(P)
Specify the primary DNS server when “DHCP” is “Off”.
*1
DNS Server
(S)
Specify the secondary DNS server when “DHCP” is “Off”.
*1
Network
Information
MAC
Address
The MAC address of this unit is shown. The MAC address is also used
as a vTuner ID.
Status
The network status of this unit is shown (“Connected” or “Not
connected”).
System ID
The system ID number is shown.
Network Standby
On,
Off
Select “On” to enable the network standby mode.
Auto Power Down
4 Hours,
8 Hours,
12 Hours,
Off
This unit automatically enters standby mode if it is left turned on for
the selected time without playback or any other operation being
performed.
Dimmer
–3 to
0
Adjust the brightness of the front panel display.
Firmware Version
The firmware version of this unit is shown.
Firmware Update
Network
,
USB
Update the firmware of this unit after selecting “Network” or “USB”.
When “Press ENTER to start” appears, press ENTER to start firmware
update. Do not operate this unit until “UPDATE SUCCESS” appears.
Then turn off this unit once and turn it on again.