Yamaha CL3 Owner's Manual - Page 56
Input/output characteristics, DIGITAL INPUT & OUTPUT CHARACTERISTICS
View all Yamaha CL3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 56 highlights
Specifications Input/output characteristics ANALOG INPUT CHARACTERISTICS Input Terminals OMNI IN 1-8 TALKBACK GAIN +66dB +18dB +17dB -6dB +64dB +20dB Actual Load Impedance 10kΩ 3kΩ 10kΩ For Use With Nominal 50-600Ω Mics & 600Ω Lines 50-600Ω Mics & 600Ω Lines Sensitivity*1 -82dBu (61.6μV) -34dBu (15.5mV) -33dBu (17.4mV) -10dBu (245mV) -70dBu (0.245mV) -26dBu (38.8mV) Input Level Nominal -62dBu (0.616mV) -14dBu (155mV) -13dBu (174mV) +10dBu (2.45V) -60dBu (0.775mV) -16dBu (0.123V) Max. before clip -42dBu (6.16mV) +6dBu (1.55V) +7dBu (1.74V) +30dBu (24.5V) -40dBu (7.75mV) +4dBu (1.23V) Connector XLR-3-31 type (Balanced)*2 XLR-3-31 type (Balanced)*2 *1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (all faders and level controls are maximum position.) *2. XLR-3-31 type connectors are balanced. (1= GND, 2= HOT, 3= COLD) *3. In these specifications, 0dBu= 0.775 Vrms. *4. All input AD converters are 24bit linear, 128times oversampling. *5. +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled switches. ANALOG OUTPUT CHARACTERISTICS Output Terminals Actual Source For Use With Impedance Nominal GAIN SW*5 OMNI OUT 1-8 75Ω +24dB (default) 600Ω Lines +18dB PHONES 8Ω Phones - 15Ω 40Ω Phones - Output Level Nominal Max. before clip Connector +4dBu (1.23V) -2dBu (616mV) +24dBu (12.3V) XLR-3-32 type +18dBu (6.16V) (Balanced)*1 75mW*6 65mW*6 150mW 150mW Stereo Phone Jack (TRS) (Unbalanced)*2 *1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD) *2. PHONES stereo phone jack is unbalanced. (Tip= LEFT, Ring= RIGHT, Sleeve= GND) *3. In these specifications, 0dBu= 0.775 Vrms. *4. All output DA converters are 24bit, 128times oversampling. *5. There are switches inside the body to preset the maximum output level. *6. The position of the level control is 10dB lowered from Max. DIGITAL INPUT & OUTPUT CHARACTERISTICS Terminal Primary/Secondary Format Dante Data length Level 24bit or 32bit 1000Base-T Audio 64ch Input/64ch Output @48kHz Connector EtherCON Cat5e DIGITAL OUTPUT CHARACTERISTICS Terminal DIGITAL OUT AES/EBU Format AES/EBU Professional Use Data Length 24bit *1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD) Level RS422 Connector XLR-3-32 type (Balanced)*1 I/O SLOT (1-3) CHARACTERISTICS Each I/O Slot accepts a mini-YGDAI card. Only Slot1 has a serial interface. CONTROL I/O CHARACTERISTICS Terminal MIDI IN OUT WORD CLOCK IN OUT GPI (5IN/5OUT) NETWORK LAMP (CL5: x3, CL3: x2, CL1: x1) USB HOST DC POWER INPUT METER (CL3/CL1 only) Format MIDI MIDI - - - IEEE802.3 - USB 2.0 - - Level - - TTL/75Ω terminated TTL/75Ω - 10BASE-T/100Base-TX 0V-12V*4 - - - *1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA) Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA *2. 4pin= +12V, 3pin= GND, Lamp rating 5W. Voltage control by software. Connector DIN Connector 5P DIN Connector 5P BNC Connector BNC Connector D Sub Connector 15P (Female)*1 RJ-45 XLR-4-31 type*2 USB A Connector (Female) JL05 Connector D Sub Connector 9P (Female) 56 Owner's Manual