Yamaha DSP-A1092 Owner's Manual - Page 21

Front Effect Output Jacks, Rear Output Jacks

Get Yamaha DSP-A1092 PDF manuals and user guides View all Yamaha DSP-A1092 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English D PRE OUT Jacks Main-channel line output. Connected with jumper bars to MAIN IN jacks when the built-in amplifier is used. Connected to input jacks of external stereo power amplifier (MAIN IN or TAPE PLAY jacks of integrated amplifier or receiver) when using external amplification. E MAIN IN Jacks Line input to built-in main-channel amplifier. Connected with jumper bars to PRE OUT jacks when the built-in amplifier is used. Not connected when using an external power amplifier. F SUBWOOFER Jacks When using one subwoofer, connect its amplifier input to either of these jacks. When using two subwoofers, connect their amplifiers to these jacks respectively. Frequencies below 90 Hz distributed from the main, center and/or rear channels are output to these jacks. Signals of LFE (low frequency effect) generated when the Dolby Digital (AC-3) is decoded are also output if they are assigned to these jacks. G FRONT EFFECT OUTPUT Jacks Front-channel line output. Can be connected to input jacks of an external stereo power amplifier driving the front effect speakers. H REAR OUTPUT Jacks Rear-channel line output. Can be connected to input jacks of an external stereo power amplifier driving the rear speakers. I MAIN SPEAKERS Terminals This unit is equipped with 2 sets of MAIN SPEAKERS terminals to allow you to connect 2 main speaker systems to this unit. When using this unit's built-in main-channel amplifier, connect the main speakers here. The jumper bars must be plugged in to connect the MAIN IN jacks to the PRE OUT jacks. J IMPEDANCE SELECTOR Switch Select the position whose requirements your speaker system meets. K SWITCHED AC OUTLET(S) You may plug other audio/video units into these sockets as long as their combined power consumption does not exceed the specified value shown. "Switched" means that these components are turned on and off by this unit's power switch. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
19
English
D
PRE OUT Jacks
Main-channel line output. Connected with jumper bars to MAIN
IN jacks when the built-in amplifier is used. Connected to input
jacks of external stereo power amplifier (MAIN IN or TAPE
PLAY jacks of integrated amplifier or receiver) when using
external amplification.
E
MAIN IN Jacks
Line input to built-in main-channel amplifier. Connected with
jumper bars to PRE OUT jacks when the built-in amplifier is
used. Not connected when using an external power amplifier.
F
SUBWOOFER Jacks
When using one subwoofer, connect its amplifier input to either
of these jacks. When using two subwoofers, connect their
amplifiers to these jacks respectively.
Frequencies below 90 Hz distributed from the main, center
and/or rear channels are output to these jacks.
Signals of LFE (low frequency effect) generated when the
Dolby Digital (AC-3) is decoded are also output if they are
assigned to these jacks.
G
FRONT EFFECT OUTPUT Jacks
Front-channel line output. Can be connected to input jacks of
an external stereo power amplifier driving the front effect
speakers.
H
REAR OUTPUT Jacks
Rear-channel line output. Can be connected to input jacks of
an external stereo power amplifier driving the rear speakers.
I
MAIN SPEAKERS Terminals
This unit is equipped with 2 sets of MAIN SPEAKERS terminals
to allow you to connect 2 main speaker systems to this unit.
When using this unit’s built-in main-channel amplifier, connect
the main speakers here. The jumper bars must be plugged in to
connect the MAIN IN jacks to the PRE OUT jacks.
J
IMPEDANCE SELECTOR Switch
Select the position whose requirements your speaker system
meets.
K
SWITCHED AC OUTLET(S)
You may plug other audio/video units into these sockets as long
as their combined power consumption does not exceed the
specified value shown. “Switched” means that these
components are turned on and off by this unit’s power switch.