Yamaha EMX660 Owner's Manual - Page 15
As a band PA, Connections
View all Yamaha EMX660 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
As a band PA 15 As a band PA Here is an example of using the EMX660 as a small PA for a band. In this example, the monitor speakers are being sent a mix that is independent of the MAIN speaker mix. An external effect such as delay or reverb is also being used. Connections • Connect mics or instruments, such as keyboards, to the channel input jacks 1-6. • Connect the main speakers to the POWER AMP 1 A/B jacks, and connect the monitor speakers to the POWER AMP 2 A/B jacks. • If you will be using an external effect such as delay or reverb, connect the EMX660's EFFECT OUT jack to the input jack of the external effect, and connect the output jack of the external effect to the EMX660's AUX IN jack. Note: Set the power amp select switch of the POWER AMP section to the "MAIN MONITOR" position. If you are using an external effect, we recommend that you turn down the EFFECT RTN controls of the MAIN and MONITOR sections. If the external effect has a stereo output, it is possible to connect its output jacks to the LINE jacks of channels 5. However in this case, be sure that the EFFECT controls are turned all the way down for the channels into which the effect sound is being input. If the EFFECT controls are raised, feedback will occur, and your speakers may be damaged. Main Speakers Monitors Speakers 1 HIGH " 2 HIGH Power AMP 1 # 3 HIGH 4 HIGH 5 HIGH 6 HIGH -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 MID MID MID MID MID MID -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 LOW LOW LOW LOW LOW LOW -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 MONI MONI MONI MONI MONI MONI 0 10 0 10 0 10 0 10 0 10 0 10 EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT 0 10 0 10 0 10 0 10 0 10 0 10 LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL 0 10 0 10 0 10 0 10 PAD PAD PAD PAD 1 2 3 4 0 10 5 0 10 6 VO. ECHO 1 VO. ECHO 2 VO. REV. 1 VO. REV. 2 HALL. 1 HALL. 2 ROOM PLATE ON DIGITAL EFFECT " Power AMP 2 # +12 +12 +6 • 6 • 6 +3 • • 0 0 0 • • 6 6 -5 • • -12 -12 -10 125 250 500 1k 2k 4k 8k POWER ON OFF PHANTOM 0 10 EFFECT RTN 0 10 TAPE IN MONITOR 0 10 MASTER +12 +12 +6 • 6 • 6 +3 • 0 • 0 0 • • 6 6 -5 • • -12 -12 -10 125 250 500 1k 2k 4k 8k 0 10 EFFECT RTN 0 10 AUX IN 0 10 TAPE IN MAIN 0 10 MASTER 2AMPs 300W 300W 1 2 LIMITER MAIN BRIDGE MAIN MAIN MAIN MONITOR POWER AMP Hi-Z Hi-Z Hi-Z Hi-Z 1 LINE 2 1 INST 2 EFFECT OUT Lo-Z Lo-Z Lo-Z Lo-Z MIC MIC FOOT SW MONITOR TAPE REC 1 IN OUT1 AUX IN 2 MAIN 2 SEE REAR PANEL CAUTION EEEngine INPUT OUTPUT Power amp select switch MAIN BRIDGE MAIN MAIN MAIN MONITOR Microphone Keyboard 1 Electric bass 88 Effects Processor Electric-acoustic guitar *1. Although this example shows an external effects processor and foot- Footswitch (YAMAHA FC5) switch, which is used to turn on and off the built-in digital effects processor, connected to the EMX660, in practice, only one effects processor, internal or external, will be used at a time, so the footswitch is not required when using external effects. EMX660-Owner's Manual