Yamaha GX-700VCD Owner's Manual - Page 17

Setting the clock, Adjusting brightness of the display, DISPLAY, TIME ADJ, FREQUENCY STEP, VOLUME

Get Yamaha GX-700VCD PDF manuals and user guides View all Yamaha GX-700VCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English Setting the clock DISC 1 DISC 2 DISC 3 DISC CHANGE OPEN / CLOSE 3-DISC VCD CHANGER STANDBY TIMER PRESET/ TUNING/ BAND A/B/C/D/E VOLUME DOWN UP PHONES 1 MIC 2 BASS TREBLE MIC MIXING MIN MAX PROGRAM B.BOOST MUSIC INPUT INPUT KARAOKE RANDOM REPEAT TIME MODE HOUR MIN DOLBY NR REC/PAUSE AUTO/MANUAL MEMORY DISPLAY TIMER TIME ADJ STANDBY/ON AUTO REVERSE CASSETTE DECK DOLBY B NR DIRECTION 1 DISPLAY 2 RANDOM REPEAT HOUR MIN MEMORY TIME ADJ 3 RANDOM REPEAT HOUR MIN MEMORY TIME ADJ Changes. Changes. Preparations and connections 1 While the power is on, press DISPLAY to display the time. 2 While holding TIME ADJ pressed, press HOUR and set the hour. * Press HOUR once to advance the time by 1 hour. Press and hold to advance continuously. 3 While holding TIME ADJ pressed, press MIN and set the minute. * Press MIN once to advance the time by 1 minute. Press and hold to advance continuously. * The hour setting will not advance even if minute is advanced from "59" to "00". Singapore model uses a 24-hour display. For China and General models, either the 24-hour display or the 12-hour display [shown by "AM (PM) 12:00"] is selected depending on the setting of the FREQUENCY STEP switch on the rear panel, so you cannot select the desired type freely. Note In the event of a power failure or when the AC supply lead is disconnected, the time display will go out, however, the clock will function for about 5 minutes without any power supply. Otherwise, the time display will flash on and off to indicate that the time must be reset. Adjusting brightness of the display DISC 1 DISC 2 DISC 3 DISC CHANGE OPEN / CLOSE PRESET/ TUNING/ BAND A/B/C/D/E VOLUME DOWN UP PROGRAM B.BOOST MUSIC INPUT INPUT KARAOKE RANDOM REPEAT TIME MODE HOUR MIN DOLBY NR REC/PAUSE AUTO/MANUAL MEMORY DISPLAY TIMER TIME ADJ STANDBY/ON VOLUME DISPLAY If desired, you can adjust the brightness of the display. Press and hold DISPLAY for more than 2 seconds so that "DIMMER ±0" appears on the display. While holding DISPLAY pressed, turn VOLUME clockwise to increase or counterclockwise to decrease brightness. Control range: ±0 to -6 (Preset value: ±0) E-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
E-9
English
DISC
1
DISC
2
DISC
3
DOWN
UP
VOLUME
STANDBY/ON
PROGRAM
B.BOOST
MUSIC
INPUT
INPUT
MIN
PRESET
/
TUNING
/
BAND
A
/
B
/
C
/
D
/
E
DISC CHANGE
OPEN
/
CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE
DOLBY NR
HOUR
RANDOM
REPEAT
TIME
DISPLAY
MODE
KARAOKE
DISC
1
DISC
2
DISC
3
STANDBY
TIMER
DOWN
UP
VOLUME
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DIRECTION
PROGRAM
B.BOOST
MUSIC
INPUT
INPUT
PHONES
MIN
PRESET
/
TUNING
/
BAND
A
/
B
/
C
/
D
/
E
DISC CHANGE
OPEN
/
CLOSE
BASS
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE
DOLBY NR
HOUR
RANDOM
REPEAT
TIME
DISPLAY
MODE
TREBLE
MIC MIXING
MIN
MAX
MIC
2
KARAOKE
1
2
3
RANDOM
REPEAT
HOUR
MIN
DISPLAY
MEMORY
TIME ADJ
MEMORY
TIME ADJ
RANDOM
REPEAT
HOUR
MIN
3–DISC VCD CHANGER
1
While the power is on, press
DISPLAY
to display the time.
2
While holding
TIME ADJ
pressed, press
HOUR
and set the
hour.
*
Press
HOUR
once to advance the time by 1hour. Press
and hold to advance continuously.
3
While holding
TIME ADJ
pressed, press
MIN
and set the
minute.
*
Press
MIN
once to advance the time by 1
minute. Press and hold to advance continuously.
*
The hour setting will not advance even if minute is
advanced from “59” to “00”.
Singapore model uses a 24-hour display. For China and
General models, either the 24-hour display or the 12-hour
display [shown by “AM (PM) 12:00”] is selected depending
on the setting of the
FREQUENCY STEP
switch on the
rear panel, so you cannot select the desired type freely.
Note
In the event of a power failure or when the AC supply lead is
disconnected,
the time display will go out, however, the clock
will function for about 5 minutes without any power supply.
Otherwise, the time display will flash on and off to indicate that
the time must be reset.
If desired, you can adjust the brightness of the display.
Press and hold
DISPLAY
for more than 2 seconds so that
“DIMMER ±0” appears on the display.
While holding
DISPLAY
pressed, turn
VOLUME
clockwise to
increase or counterclockwise to decrease brightness.
Control range:
±0 to –6 (Preset value: ±0)
Setting the clock
Adjusting brightness of the display
Changes.
Changes.
Preparations and connections
VOLUME
DISPLAY