Yamaha HTR-6025 Owner's Manual - Page 59

Remote control, Resetting the system, set this unit to the standby mode.

Page 59 highlights

■ Remote control Troubleshooting Problem The remote control does not work nor function properly. Cause Remedy Wrong distance or angle. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. The batteries are weak. The remote control code is not correctly set. Even if the remote control code is correctly set, there are some models that do not respond to the remote control. The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. Reposition this unit. Replace all batteries. Set the remote control code correctly using "List of remote control codes" at the end of this manual. Try setting another code for the same manufacturer using "List of remote control codes" at the end of this manual. See page 20 - 3 49 49 ■ Resetting the system Use this feature to reset all the parameters of this unit to the initial factory settings. 1 Press 1STANDBY/ON on the front panel to set this unit to the standby mode. 2 Press and hold 0TONE CONTROL and then press 1STANDBY/ON to turn on this unit. The advanced setup menu appears in the front panel display. Notes • This procedure completely resets all the parameters of this unit including the set menu parameters. However, the advanced setup menu parameters will not be initialized. • The initial factory settings are activated next time you turn on this unit. y To cancel the initialization procedure at any time without making any changes, press BSTRAIGHT repeatedly to select "CANCEL" and then press 1STANDBY/ON. 3 Press APROGRAM l / h to select "PRESET". 4 Press BSTRAIGHT repeatedly to select "RESET". Select "CANCEL" to cancel the initialization procedure without making any changes. 5 Press 1STANDBY/ON to confirm your selection and set this unit to the standby mode. ADDITIONAL INFORMATION English 55 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73

55
En
Troubleshooting
ADDITIONAL
INFORMATION
English
Remote control
Resetting the system
Use this feature to reset all the parameters of this unit to
the initial factory settings.
1
Press
1
STANDBY/ON
on the front panel to
set this unit to the standby mode.
2
Press and hold
0
TONE CONTROL
and
then press
1
STANDBY/ON
to turn on this
unit.
The advanced setup menu appears in the front panel
display.
3
Press
A
PROGRAM
l
/
h
to select
“PRESET”.
4
Press
B
STRAIGHT
repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
5
Press
1
STANDBY/ON
to confirm your
selection and set this unit to the standby
mode.
This procedure completely resets all the parameters of this unit
including the set menu parameters. However, the advanced
setup menu parameters will not be initialized.
The initial factory settings are activated next time you turn on
this unit.
y
To cancel the initialization procedure at any time without making
any changes, press
B
STRAIGHT
repeatedly to select
“CANCEL” and then press
1
STANDBY/ON
.
Problem
Cause
Remedy
See
page
The remote control
does not work nor
function properly.
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
20
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
49
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
49
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Notes