Yamaha MX200-16 Owner's Manual - Page 5

AUX1-4 controls, PAN panpot control, Channel ON switch, Channel fader

Get Yamaha MX200-16 PDF manuals and user guides View all Yamaha MX200-16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

7 AUX1-4 controls These knobs control the level of the signals sent to the AUX buses. • The AUX1 and AUX2 controls are pre-fader, and the signal levels sent to the AUX 1 and 2 buses will be unaffected by the channel fader setting. • The AUX3 and AUX 4 controls are post-fader, and the signal levels sent to the AUX 3 and 3 buses will be affected by the channel fader setting. 8 PAN (panpot) control This knob assigns the signal of each channel to the STEREO L, R bus, determining the stereo position of the sound. 9 Channel ON switch When this switch is on, the signal of each channel will be sent to the STEREO L, R bus and the AUX1-4 buses. When this switch is off, the output signal to each bus will be muted completely. This switch should be turned off for unused channels. 0 Channel PFL switch This switch allows you to monitor the pre-fader channel input signal through headphones. It is convenient to use PFL when you wish to check the sound of the input signal, or when troubleshooting a specific channel. A Channel fader This fader controls the output level of the input channel signal, determining the volume balance between channels. The channel fader should be lowered for unused channels. CTRL STEREO AUX PFL AFL PFL AFL 4 2 3 1 L R INPUT A 1-* INPUT B 1-* PHANTOM OFF (INPUT A) ON PHANTOM (PHANTOM) (+48V) INPUT CH INSERT I/O 0dB 1-* PEAK PAD HA HPF 3BAND EQ ON A 20dB GAIN 80 B LOW MID HIGH *=8,12,16,24 PAN AUX 1 AUX 2 AUX 3 (+V) PFL 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
3
7
AUX1–4 controls
These knobs control the level of the signals sent to the
AUX buses.
•
The AUX1 and AUX2 controls are pre-fader, and the
signal levels sent to the AUX 1 and 2 buses will be un-
affected by the channel fader setting.
•
The AUX3 and AUX 4 controls are post-fader, and the
signal levels sent to the AUX 3 and 3 buses will be af-
fected by the channel fader setting.
8
PAN (panpot) control
This knob assigns the signal of each channel to the
STEREO L, R bus, determining the stereo position of the
sound.
9
Channel ON switch
When this switch is on, the signal of each channel will be
sent to the STEREO L, R bus and the AUX1–4 buses.
When this switch is off, the output signal to each bus will
be muted completely. This switch should be turned off for
unused channels.
0
Channel PFL switch
This switch allows you to monitor the pre-fader channel
input signal through headphones.
It is convenient to use PFL when you wish to check the
sound of the input signal, or when troubleshooting a
specific channel.
A
Channel fader
This fader controls the output level of the input channel
signal, determining the volume balance between channels.
The channel fader should be lowered for unused channels.
(+V)
0dB 1-*
*=8,12,16,24
INPUT B
INPUT A
1-*
1-*
PHANTOM
(PHANTOM)
(INPUT A)
OFF
ON
PHANTOM
(+48V)
AUX
CTRL
AFL
PFL
AFL
PFL
4
3
2
1
R
L
STEREO
PFL
AUX 3
AUX 2
PAN
AUX 1
EQ
3BAND
HA
PAD
A
B
20dB
GAIN
HPF
80
LOW
MID
HIGH
ON
PEAK
INSERT I/O
INPUT CH