Yamaha MY8-ADDA96 MY8-ADDA96 Owners Manual - Page 2
Fcc Information, Precautions - manual
View all Yamaha MY8-ADDA96 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Thank you for purchasing an AD/DA card for use with Yamaha digital audio equipment. Refer to the respective owner's manual for installation information. As well as securing the card in place, the fixing screws act as an electrical ground, so be sure to screw them in tightly. PRECAUTIONS WARNING Failure to observe the following warnings may lead to fatality or serious injury from fire or electric shock. • Before installing the card, you must refer to the owner's manual of the host device or to the Yamaha website ("Guidance on the use of Mini-YGDAI cards" page) to verify that your host device supports this card, and to verify the number of cards that can be installed in combination with other Yamaha or third-party cards. Yamaha website: http://www.yamahaproaudio.com/ • Do not attempt to disassemble or modify the card. Do not apply excessive force to board connectors or other board components. (Mishandling of board may lead to shock, fire hazard, or equipment failure.) • Be sure to disconnect the power cable from the main unit before installing this card (to eliminate shock hazard). CAUTION Failure to observe the following precautions may lead to personal injury, or may result in damage to equipment or other property. • Do not touch the board's metallic leads (pins) when handling the card. (Pins are sharp and may cause hand cuts.) • The card is electrostatic-sensitive. Before handling the card, you should briefly touch the main unit's metal casing with your bare hand so as to drain off any static charge from your body. Yamaha assumes no responsibility for data loss, equipment damage, or injury caused by inappropriate handling or usage. * The company names and product names in this Owner's Manual are the trademarks or registered trademarks of their respective companies. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. 2