Yamaha MY8-ADDA96 MY8-ADDA96 Owners Manual - Page 7

Cable Preparation, ANALOG INPUT CHARACTERISTICS, Pin Assignment of Euroblock connectors - ad da

Get Yamaha MY8-ADDA96 PDF manuals and user guides View all Yamaha MY8-ADDA96 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Cable Preparation Shielded Cable 7mm 30mm Remove the shield (as shown in the illustration) from the tip of the cable to which you are connecting the included Euroblock plug. Supported wire gauge: 16 - 24 AWG • Be sure to use a shielded cable. • Do not solder the bare part of the core wire of the cable. Entfernen Sie die Schirmung (siehe Abbildung) an der Spitze des Kabels, an das Sie den beiliegenden Euroblock-Stecker anschließen möchten. Unterstütze Aderstärken: 16~24 AWG • Verwenden Sie ausschließlich geschirmtes Kabel. • Verlöten Sie niemals den blanken Teil des Kabelkerns. Enlevez la protection (comme indiqué dans l'illustration) du bout du câble auquel vous branchez la prise Euroblock incluse. Type de câble accepté: 16~24 AWG • Utilisez un câble blindé. • Ne soudez pas la partie dénudée du fil central du câble. Extraiga la protección (como se muestra en la ilustración) de la punta del cable al que está conectando el conector Euroblock incluido. Tamaño permitido del cable: 16~24 AWG • Asegúrese de usar un cable blindado. • No suelde la parte pelada del núcleo del cable. 8(  Specifications 1. ANALOG INPUT CHARACTERISTICS Input Terminals IN 1-8 Actual Load Impedance 10k Ω For Use With Nominal 600Ω Lines Input level Max. before clip +24 dBu (12.28 V) Connector Euroblock (balanced) *1. In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms. *2. AD converters are 24 bit linear, 128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz). 2. ANALOG OUTPUT CHARACTERISTICS Output Terminals OUT 1-8 Actual Source Impedance 75 Ω For Use With Nominal 10kΩ Lines Output level Max. before clip +24 dBu (12.28 V) Connector Euroblock (balanced) *1. In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms. *2. DA converters are 24 bit linear,128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz). 3. Pin Assignment of Euroblock connectors IN/OUT 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 + -G +- G + -G + -G CH8 CH7 CH6 CH5 + -G + -G + - G + -G CH4 CH3 CH2 CH1 4. Included Accessories 12-pin Euroblock plug x4 Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
7
Remove the shield (as shown in the illustration) from the tip of the cable to which you are connecting the included Euroblock plug.
Supported wire gauge: 16 - 24 AWG
Entfernen Sie die Schirmung (siehe Abbildung) an der Spitze des Kabels, an das Sie den beiliegenden Euroblock-Stecker
anschließen möchten.
Unterstütze Aderstärken: 16~24 AWG
Enlevez la protection (comme indiqué dans l’illustration) du bout du câble auquel vous branchez la prise Euroblock incluse.
Type de câble accepté: 16~24 AWG
Extraiga la protección (como se muestra en la ilustración) de la punta del cable al que está conectando el conector Euroblock incluido.
Tamaño permitido del cable: 16~24 AWG
付属のユーロブロックプラグに取り付けるケーブルは、図のようにむき出しにしてください。
使用可能電線径 : 16 ～ 24 AWG
ケーブルは、必ずシールド線を使用してください。
ケーブルのむき出し部分に半田めっきしないでください。
1. ANALOG INPUT CHARACTERISTICS
*1.
In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms.
*2.
AD converters are 24 bit linear, 128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz).
2. ANALOG OUTPUT CHARACTERISTICS
*1.
In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms.
*2.
DA converters are 24 bit linear,128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz).
3. Pin Assignment of Euroblock connectors
4. Included Accessories
12-pin Euroblock plug x4
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to
change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not
be the same in every locale, please check with your Yamaha dealer.
Input Terminals
Actual Load Impedance
For Use With Nominal
Input level
Connector
Max. before clip
IN 1–8
10k
Ω
600
Ω
Lines
+24 dBu (12.28 V)
Euroblock (balanced)
Output Terminals
Actual Source Impedance
For Use With Nominal
Output level
Connector
Max. before clip
OUT 1–8
75
Ω
10k
Ω
Lines
+24 dBu (12.28 V)
Euroblock (balanced)
7mm
30mm
Cable Preparation
Shielded Cable
•
Be sure to use a shielded cable.
•
Do not solder the bare part of the core wire of the cable.
•
Verwenden Sie ausschließlich geschirmtes Kabel.
•
Verlöten Sie niemals den blanken Teil des Kabelkerns.
•
Utilisez un câble blindé.
•
Ne soudez pas la partie dénudée du fil central du câble.
•
Asegúrese de usar un cable blindado.
•
No suelde la parte pelada del núcleo del cable.
Specifications
12
11 10
9
8
6
4
1
+
–
G
–
G
+
–
G
–
G
+
–
G
–
G
+
–
G
–
G
CH4
CH3
CH2
CH1
CH8
CH7
CH6
CH5
2
3
5
7
12
11 10
9
8
6
4
1
2
3
5
7
+
+
+
+
IN/OUT