Home » Yamaha Manuals » Musical Instruments » Yamaha P-250 » Manual Viewer

Yamaha P-250 Owner's Manual - Page 69

Assigning the Pedal 2 function [Pedal 2]

Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Edit Operation Editing a Voice in Detail [VOICE EDIT] • Refer to page 61 for general information on setting the parameters. • Refer to pages 3-5 of the separate "Data List" for information on the default parameter settings. • All parameters accessed via the [VOICE EDIT] button are performance parameters (page 30). ■ Assigning the Pedal 1 function [Pedal 1] ■ Assigning the Pedal 2 function [Pedal 2] ■ Assigning the Pedal 3 function [Pedal 3] You can assign a function to a pedal connected to the pedal jack. Press the D [-]/[+] buttons to select one of the following functions: Sustain...........On/Off switch-type damper (page 39) SustainCont ... Damper effect that sustains notes longer when you press the pedal further down (page 39) Sostenuto.......Sostenuto pedal (page 39) Soft Soft pedal (page 39) Expression ..... Adds accents to notes being played. Off No function is assigned. ■ Assigning the Pedal 4 function [Pedal 4] Press the D [-]/[+] buttons to select one of the following functions: Sustain...........On/Off switch-type damper (page 39) SustainCont ... Damper effect that sustains notes longer when you press the pedal further down (page 39) Sostenuto.......Sostenuto pedal (page 39) Soft Soft pedal (page 39) Expression ..... Adds accents to notes being played. ReverbSend ... Adds reverb accents to notes being played. ChorusSend ... Adds chorus accents to notes being played. Brightness ......Adds brightness accents to notes being played. Harmonic Content..........Adds resonance accents to notes being played. After Touch .... Adds after-touch accents to notes being played. (MIDI transmit only) Ctrl#0-#119 ..Adds accents by controller #0-119 to notes being played. (MIDI transmit only) Off No function is assigned. TIP Recommended pedals: For the Sustain, SustainCont, Sostenuto, and Soft functions, use FC3, FC4/FC5, FC7 pedals. For other functions, use FC7. ■ Assigning the modulation wheel function [Modulation] You can specify the parameter controlled by the modulation wheel. Press the D [-]/[+] buttons to select one of the following functions: Expression......Adds accents to notes being played. Main Volume ..........Changes the volume level of the Main part notes being played. Layer Volume ..........Changes the volume level of the Layer part notes being played. (Displayed only when Main is in Dual mode.) LeftVolume ....Changes the volume level of the Left part note being played. LeftLayer Volume ..........Changes the volume level of the LeftLayer part note being played. (Displayed only when Left is in Dual mode.) RotarySpeed...Changes the rotary speaker's rotation speed during performance VibeRotor ......Changes the vibraphone's vibrato speed during performance Modulation ....Adds modulation accents. ReverbSend....Adds reverb accents to notes being played. ChorusSend ...Adds chorus accents to notes being played. Brightness ......Adds brightness accents to notes being played. Harmonic ......Adds resonance accents to notes being played. After Touch.....Adds after-touch accents to notes being played. (MIDI transmit only) Ctrl#0-#119 ..Adds accents by controller #0-119 to notes being played. (MIDI transmit only) Off No function is assigned. P-250 69

Section	Page
PRECAUTIONS	3
PLEASE READ CAREFULLY BEFORE PROCEEDING	3
* Please keep this manual in a safe place for future reference.	3
WARNING	3
CAUTION	3
Introduction	5
How to Use this Manual	5
Accessories and Options	6
Features	6
Basic Operation	13
Names and Functions	14
Top Panel	14
Rear Panel Controls	15
Setting Up	16
Installing the Accessories	16
Music rest	16
Pedal	16
Before Powering Up	16
Powering Up	16
Connecting to External Devices	17
Connecting to External Audio Equipment	17
Connectingstereopowered speakers	17
Connecting to a external instrument	17
Connecting to a mixer	17
Connecting External MIDI Equipment	18
Controlling an external device from the P-250	18
Controlling the P-250 from an external device	18
Recording your performance on the P-250 to an external MIDI sequencer (such as the QY series), or...	18
Controlling another MIDI device via the MIDI [THRU] connector	18
Connecting to a Personal Computer	19
1 USB connection (the computer’s USB port to the P-250 [USB] connector)	19
2Serialconnection(computer’s serial port to P-250 [TO HOST] connector)	20
3 MIDIconnection(thecomputer’s MIDI interface or external MIDI interface to the P-250 MIDI IN ...	22
Connecting Pedals	23
Connecting headphones	23
P-250 Quick Guide	24
Listening to Demo and Preset Songs	24
Listening to the demo songs	24
Listening to the preset songs	25
Selecting, Editing, and Storing a Voice	26
Selecting, Editing, and Storing a Performance	27
Editing a Voice and Storing It as a Performance	27
P-250 Design	28
Voice	28
Performances	30
Performance parameters	30
Performance file	32
Songs	33
Song file	33
About P-250 Memory	33
Storage memory	33
Current memory	33
Basic Operation	34
Selecting a Voice	34
Playing in Dual Mode	35
Dual mode using voices in different voice groups	35
Dual mode using voices in the same voice group	35
Playing in Split Mode	36
Effect Structure	37
System effects	37
Insertion effects	37
Using the Effects	37
Reverb	37
Chorus	37
Using the Master Equalizer	38
Using the Pitch Bend and Modulation Wheels	38
Pitch bend wheel	38
Modulation wheel	38
Using Pedals	39
Applying the sustain effect	39
Applying the sostenuto effect	39
Applying the soft effect	39
Applying the expression effect	39
Using Panel Lock	39
Toggling MIDI Transmission On/Off	40
Transmitting MIDI Panic Signals	40
Performance Operation	41
Selecting a Performance	41
Handling Performance Files [PERFORM.FILE]	42
Basic Operation for the Performance File	42
Storing a Performance [Performance]	43
Renaming a Performance [Perf.Name]	43
Saving a Performance File to Storage Memory [SaveToMemory]	44
Loading a Performance File from Storage Memory [LoadFromMem.]	44
Deleting a Performance File [DeleteFile]	45
Renaming a Performance File [RenameFile]	45
Song Operation	46
Recording Songs	46
Recording a New Song	47
Recording	47
Re-recording part of a song	48
Other Recording Techniques	49
Adding data to or recording over an existing song	49
Changing the voice or tempo after recording	49
Adjusting the volume balance between playback and the sound of your playing by using the [SONG BA...	49
Recording in Dual or Split mode	50
Song Playback	51
Playback	51
Handling Song Files [SONG FILE]	53
Basic Song File Operation	53
Saving a Song File in Storage Memory [SaveToMemory]	54
Deleting a Song File from Storage Memory [DeleteSong]	54
Renaming a Song (Song File) [RenameSong]	55
Changing the On-Screen Character Type [CharacterCode]	55
Edit Operation	57
Editing	58
Parameter List	58
Basic Editing Flow	61
Settings for Song Recording and Playback [SONG SETTING]	62
Correcting note timing [Quantize]	62
Specifying whether playback starts immediately along with the first voicing [QuickPlay]	62
Auditioning channel [ChannelListen]	63
Deleting data from a channel [ChannelClear]	63
Specifying the range and playing back repeatedly [FromToRepeat]	63
Specifying a phrase for playback by phrase number [PhraseMark]	63
Playing back a song repeatedly [SongRepeat]	64
Setting the click time signature [TimeSignature]	64
Setting the click volume [ClickVolume]	64
Turning the click on/off [ClickOnOff]	64
Editing a Voice in Detail [VOICE EDIT]	65
Basic voice editing using [VOICE EDIT]	65
Setting the octave* [Octave]	65
Setting the volume level* [Volume]	65
Setting the position of the right and left channels* [Pan]	66
Adjusting fine pitch offset between two voices in Dual mode [Detune]	66
Selecting the reverb type [ReverbType]	66
Setting the reverb depth* [ReverbSend]	66
Setting the chorus type [ChorusType]	66
Setting the chorus depth* [ChorusSend]	67
Turning the chorus on/off [ChorusOnOff]	67
Selecting the insertion effect type* [Ins.Type(Ins)]	67
Setting the speed of the vibraphone vibrato effect* [VibeRotorSpeed(RotorSpeed)]	67
Turning the Vibraphone vibrato on/off* [VibeRotorOnOff (RotorOnOff)]	67
Adjusting the speed of the rotary speaker* [RotarySpeed (Rot.Speed)]	67
Adjusting the insertion effect depth* [Dry/WetBalance(Dry/Wet)]	68
Adjusting the brightness of the sound* [Brightness]	68
Adjusting the resonance effect* [HarmonicContent (Harmonic)]	68
Adjusting the low-range frequency of the part EQ* [EQ LowFreq.(EQ L.Freq)]	68
Adjusting the high-range frequency of the part EQ* [EQ HighFreq.(EQ H.Freq)]	68
Adjusting the low-range gain (amount of boost/cut) of the part EQ* [EQLowGain]	68
Adjusting the high-range gain (amount of boost/cut) of the part EQ* [EQHighGain]	68
Setting the touch sensitivity* [TouchSense]	68
Assigning the Pedal 1 function [Pedal 1]	69
Assigning the Pedal 2 function [Pedal 2]	69
Assigning the Pedal 3 function [Pedal 3]	69
Assigning the Pedal 4 function [Pedal 4]	69
Assigning the modulation wheel function [Modulation]	69
Setting the MSB of the Send Bank Select message* [SendBankMSB(SendMSB)]	70
Setting the LSB of the Send Bank Select message* [SendBankLSB(SendLSB)]	70
Setting the Program Change message* [SendPG#]	70
Turning the Internal tone generator on/off* [InternalTG]	70
Adjusting the Master Equalizer [MASTER EQ EDIT]	71
Setting the Master Equalizer type	71
Adjusting the low range gain of the Master Equalizer [LowGain]	71
Adjusting the low-middle range gain of the Master Equalizer [LowMidGain]	71
Adjusting the middle range gain of the Master Equalizer [MidGain]	71
Adjusting the high-middle range gain of the Master Equalizer [HighMidGain]	71
Adjusting the high range gain of the Master Equalizer [HighGain]	71
Adjusting the low frequency of the Master Equalizer [LowFreq.]	71
Adjusting the low-middle frequency of the Master Equalizer [LowMidFreq.]	71
Adjusting the middle frequency of the Master Equalizer [MidFreq.]	71
Adjusting the high-middle frequency of the Master Equalizer [HighMidFreq.]	71
Adjusting the high frequency of the Master Equalizer [HighFreq.]	71
Adjusting the low range resonance of the Master Equalizer [LowQ]	72
Adjusting the low-middle range resonance of the Master Equalizer [LowMidQ]	72
Adjusting the middle range resonance of the Master Equalizer [MidQ]	72
Adjusting the high-middle range resonance of the Master Equalizer [HighMidQ]	72
Adjusting the high range resonance of the Master Equalizer [HighQ]	72
MIDI [MIDI SETTING]	73
About MIDI	73
[MIDI] connector	73
[TO HOST] connector	73
[USB] connector	73
Setting the MIDI transmit channel [MidiOutChannel]	74
Setting the MIDI receive channel [MidiInChannel]	74
Turning the Local Control On/Off [LocalControl]	74
Specifying keyboard performance or song data to be transmitted via MIDI [MidiOutSelect]	74
Specifying the type of data received via MIDI [ReceiveParameter]	75
Specifying the type of data transmitted via MIDI [TransmitParameter]	75
Transmitting the initial settings on the panel [InitialSetup]	75
Executing Voice Data Bulk Dump [VoiceBulkDump]	75
Other Settings [OTHER SETTING]	76
Selecting a touch response [TouchResponse]	76
Fine-tuning the pitch [Tune]	76
Selecting a tuning curve for a piano voice [PianoTuningCurve]	76
Selecting a scale [Scale]	77
Setting the split point [SplitPoint]	77
Setting the key [Transpose]	77
Specifying the depth of the soft pedal [SoftPedalDepth]	77
Specifying the depth of string resonance [StringResonanceDepth]	77
Specifying the depth of sustain sampling for the damper pedal [SustainSamplingDepth]	78
Specifying the volume of the key-off sound [KeyOffSamplingDepth]	78
Selecting a pedal function for vibraphone [VibraphonePedalMode]	78
Assigning the START/STOP function to a pedal [PedalStart/Stop]	78
Selecting a type of pedal [Pedal Type]	78
Setting the point at which the pedal starts to affect the sound [HalfPedalPoint]	78
Setting the pitch bend range [PitchBendRange]	79
Assigning a function to the [SONG BALANCE] slider [SongBalanceAssign]	79
Switching the speaker on/off [Speaker]	79
Locking the Master Equalizer settings [EqualizerLock]	79
Selecting items saved at shutdown [MemoryBackUp]	79
Restoring the normal (default) settings [FactorySet]	79
Appendix	81
Message List	82
Troubleshooting	86
Midi Data Compatibility	88
Preset Voice List	90
Preset Performance List	92
Application Index	94
Listening and playing	94
Using the controllers	94
Changing the sound	94
Changing the pitch	94
Adjusting the volume Level	95
Recording, playing, and saving a song	95
Using, editing, and saving a performance	95
Connecting the P-250 to other devices	95
If you . . .	95
Index	96
2. Main Power Supply Verification: Yamaha products are manufactured specifically for the supply v...	99
3. This product may be equipped with a polarized plug (one blade wider than the other). If you ar...	99
4. Some electronic products utilize external power supplies or adapters. Do NOT connect this type...	99
5. WARNING: Do not place this product or any other objects on the power cord or place it in a pos...	99
6. Ventilation: Electronic products, unless specifically designed for enclosed installations, sho...	99
7. Temperature considerations: Electronic products should be installed in locations that do not s...	99
8. This product was NOT designed for use in wet/damp locations and should not be used near water ...	99
9. This product should be used only with the components supplied or; a cart, rack, or stand that ...	99
10. The power supply cord (plug) should be disconnected from the outlet when electronic products ...	99
11. Care should be taken that objects do not fall and liquids are not spilled into the enclosure ...	99
12. Electrical/electronic products should be serviced by a qualified service person when:	99
13. Do not attempt to service this product beyond that described in the user-maintenance instruct...	99
14. This product, either alone or in combination with an amplifier and headphones or speaker/s, m...	99

Match case Limit results 1 per page

P-250

Editing a Voice in Detail [VOICE EDIT]

Edit Operation

■

Assigning the Pedal 1 function [Pedal 1]

■

Assigning the Pedal 2 function [Pedal 2]

■

Assigning the Pedal 3 function [Pedal 3]

You can assign a function to a pedal connected to the

pedal jack.

Press the D [–]/[+] buttons to select one of the following

functions:

Sustain

...........

On/Off switch-type damper (page 39)

SustainCont ... Damper effect that sustains notes longer

when you press the pedal further down

(page 39)

Sostenuto

.......

Sostenuto pedal (page 39)

Soft

................

Soft pedal (page 39)

Expression

.....

Adds accents to notes being played.

Off

.................

No function is assigned.

■

Assigning the Pedal 4 function [Pedal 4]

Press the D [–]/[+] buttons to select one of the following

functions:

Sustain

...........

On/Off switch-type damper (page 39)

SustainCont ... Damper effect that sustains notes longer

when you press the pedal further down

(page 39)

Sostenuto

.......

Sostenuto pedal (page 39)

Soft

................

Soft pedal (page 39)

Expression

.....

Adds accents to notes being played.

ReverbSend ...Adds reverb accents to notes being

played.

ChorusSend...Adds chorus accents to notes being

played.

Brightness

......

Adds brightness accents to notes being

played.

Harmonic

Content

..........

Adds resonance accents to notes being

played.

After Touch

....

Adds after-touch accents to notes being

played. (MIDI transmit only)

Ctrl#0—#119 ..Adds accents by controller #0—119 to notes

being played.

(MIDI transmit only)

Off

.................

No function is assigned.

■

Assigning the modulation wheel function

[Modulation]

You can specify the parameter controlled by the modula-

tion wheel.

Press the D [–]/[+] buttons to select one of the following

functions:

Expression

......

Adds accents to notes being played.

Main

Volume

..........

Changes the volume level of the Main part

notes being played.

Layer

Volume

..........

Changes the volume level of the Layer

part notes being played.

(Displayed only when Main is in Dual

mode.)

LeftVolume

....

Changes the volume level of the Left part

note being played.

LeftLayer

Volume

..........

Changes the volume level of the LeftLayer

part note being played.

(Displayed only when Left is in Dual

mode.)

RotarySpeed...Changes the rotary speaker’s rotation

speed during performance

VibeRotor

......

Changes the vibraphone’s vibrato speed

during performance

Modulation

....

Adds modulation accents.

ReverbSend

....

Adds reverb accents to notes being

played.

ChorusSend ...Adds chorus accents to notes being

played.

Brightness

......

Adds brightness accents to notes being

played.

Harmonic

......

Adds resonance accents to notes being

played.

After Touch

.....

Adds after-touch accents to notes being

played. (MIDI transmit only)

Ctrl#0—#119..Adds accents by controller #0—119 to

notes being played.

(MIDI transmit only)

Off

.................

No function is assigned.

•

Refer to page 61 for general information on setting the parameters.

•

Refer to pages 3—5 of the separate “Data List” for information on the default parame-

ter settings.

•

All parameters accessed via the [VOICE EDIT] button are performance parameters (page 30).

TIP

Recommended pedals:

For the Sustain, SustainCont, Sostenuto, and Soft func-

tions, use FC3, FC4/FC5, FC7 pedals. For other functions,

use FC7.