Yamaha RX-V2090 Owner's Manual - Page 10

CONNECTING SPEAKERS, sible. If the connections are faulty, no sound will - model

Get Yamaha RX-V2090 PDF manuals and user guides View all Yamaha RX-V2090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

CONNECTING SPEAKERS Connect the respective speakers to this unit as shown below: Main speakers A Right Left Front speakers Right Left Rear speakers Right Left OUTPUT FRONT OUT LOW CENTER PASS OUT FRONT SPEAKERS REAR fo:200Hz A REAR OUT 8ΩMIN. /SPEAKER 8ΩMIN. /SPEAKER CENTER C C Right B Left A OR B: 5ΩMIN. /SPEAKER A+ B:l2ΩMIN. /SPEAKER CD D C+D C: 8ΩMIN. /SPEAKER C+ D: 4ΩMIN. /SPEAKER Main speakers B Note on main speaker connection: One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Note on center speaker connection: One or two center speakers can be connected to this unit. If you cannot place the center speaker on or under the TV, it is recommended to use two center speakers and place them on both sides of the TV to orient the center sound at the center position. When connecting two center speakers, be sure to press the CENTER speaker switch into the "C+D" position ( ) . When you use a single center speaker, set the switch to the "C" position( ) . How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and - markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. CAUTION Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit. This could damage this unit and/or the speakers. Center speaker(s) Note: Use speakers with the specified impedance shown on the rear of this unit. For connecting to the SPEAKER terminals Red: positive (+) Black: negative (-) 2 1 3 1 Unscrew the knob. 2 Insert the bare wire. [Remove approx. 5mm (1/4") insulation from the speaker wires.] 3 Tighten the knob and secure the wire. Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. (Not available on Singapore model.) Note: Use only single type banana plug cable. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
10
CONNECTING SPEAKERS
Connect the respective speakers to this unit as shown below:
A
B
C
C
C
+
D
C
A OR B: 5
Ω
MIN. /SPEAKER
A
+
B:l2
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
OUTPUT
FRONT
OUT
REAR
OUT
CENTER
OUT
LOW
PASS
fo:200Hz
8
Ω
MIN. /SPEAKER
SPEAKERS
FRONT
REAR
CENTER
C: 8
Ω
MIN. /SPEAKER
C
+
D: 4
Ω
MIN. /SPEAKER
D
D
Right
Left
Main speakers A
Front speakers
Rear speakers
Right
Left
Right
Left
Right
Left
Center speaker(s)
Main speakers B
Note on main speaker connection:
One or two speaker systems can be connected to this
unit. If you connect only one speaker system, connect
it to either the
SPEAKERS A
or
B
terminals.
Note on center speaker connection:
One or two center speakers can be connected to this
unit. If you cannot place the center speaker on or
under the TV, it is recommended to use two center
speakers and place them on both sides of the TV to
orient the center sound at the center position.
When connecting two center speakers, be sure to
press the CENTER speaker switch into the “
C+D
”
position (
) . When you use a single center speaker,
set the switch to the “C” position(
) .
How to Connect:
Connect the SPEAKERS terminals to your speakers
with wire of the proper gauge, cut as short as pos-
sible. If the connections are faulty, no sound will be
heard from the speakers. Make sure that the polarity
of the speaker wires is correct, that is, + and – mark-
ings are observed. If these wires are reversed, the
sound will be unnatural and will lack bass.
CAUTION
Do not let the bare speaker wires touch each other
and do not let them touch the metal parts of this unit.
This could damage this unit and/or the speakers.
Note:
Use speakers with the specified impedance shown on
the rear of this unit.
For connecting to the SPEAKER terminals
Red: positive (+)
Black: negative (–)
1
Unscrew the knob.
2
Insert the bare wire. [Remove
approx. 5mm (1/4") insulation
from the speaker wires.]
3
Tighten the knob and secure
the wire.
Banana Plug connections are also possible. Simply
insert the Banana Plug connector into the correspond-
ing terminal. (Not available on Singapore model.)
Note:
Use only single type banana plug cable.
1
2
3