Yamaha RX-V3000 Owner's Manual - Page 60

Remote Control in Zone 2, Introduction, Preparations, Basic Operation, Advanced, Operation, Additional

Get Yamaha RX-V3000 PDF manuals and user guides View all Yamaha RX-V3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Introduction Preparations Basic Operation ZONE 2 Remote Control in Zone 2 In the second room (Zone 2), the supplied remote control can be used for the Zone 2 remote control. You can select the input source and control the component which is located in the main room directly from the second room regardless of the listening condition in the main room. Before starting the following procedure, set REC OUT/ZONE 2 on the front panel to the SOURCE/REMOTE position. 1 Press an input button to select the source component you want to set up. 2 Press and hold LEARN for about 3 seconds by using a ballpoint pen or similar object. LEARN Flashes alternately "SETUP" and the selected component name appear alternately in the display window. 3 Press q/w to select "L:AMP". 4 Press / to select "ZONE 2". 5 Press LEARN to complete the Zone 2 setup. LEARN 6 Press SOURCE SELECT to display "Zone2" in the display window. 7 Press an input button to select the input source you want to listen to in the second room. The display window shows "2: (name of selected input)" if the remote control is in the Zone 2 mode. 8 You can control the component by using the component control area buttons. Note: • VOLUME +/- can be used to adjust the volume if you set the SET MENU item 16. ZONE2 SET, ZONE2 OUT to "VAR.". Press SOURCE SELECT / to exit from the Zone 2 mode. Advanced Operation Additional Information Appendix 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Introduction
Preparations
Basic Operation
Advanced
Operation
Additional
Information
Appendix
56
Remote Control in Zone 2
In the second room (Zone 2), the supplied remote control can be used for the Zone 2 remote control. You can select the input source and
control the component which is located in the main room directly from the second room regardless of the listening condition in the main
room.
Before starting the following procedure, set
REC OUT/ZONE 2
on the front panel to the SOURCE/REMOTE position.
1
Press an input button to select the source component you
want to set up.
2
Press and hold
LEARN
for about 3 seconds by using a
ballpoint pen or similar object.
“SETUP” and the selected component name appear
alternately in the display window.
3
Press
q
/
w
to select “L:AMP”.
4
Press
/
to select “ZONE 2”.
5
Press
LEARN
to complete the Zone 2 setup.
6
Press
SOURCE SELECT
to display “Zone2” in the
display window.
7
Press an input button to select the input source you want to
listen to in the second room.
The display window shows “2: (name of selected input)” if
the remote control is in the Zone 2 mode.
8
You can control the component by using the component
control area buttons.
Note:
•
VOLUME +/–
can be used to adjust the volume if you set the
SET MENU item 16. ZONE2 SET, ZONE2 OUT to “VAR.”.
Press
SOURCE SELECT
/
to exit from the Zone 2
mode.
ZONE 2
Flashes
alternately
LEARN
LEARN