Yamaha RX-V392 Owner's Manual - Page 14

OUTPUT terminals for driving speakers with external amplifiers, IMPEDANCE SELECTOR switch - power will not turn on

Get Yamaha RX-V392 PDF manuals and user guides View all Yamaha RX-V392 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

OUTPUT terminals (for driving speakers with external amplifiers) OUTPUT CENTER CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. SUB WOOFER SUBWOOFER OUTPUT terminal This terminal is for connecting with the input terminal of an amplifier for driving a subwoofer. This terminal outputs only frequencies below 200 Hz from the main and center channels. Note Output level of signals from these terminals are adjusted by the use of VOLUME control on the front panel or VOLUME keys on the remote control transmitter. IMPEDANCE SELECTOR switch Be sure to switch this only when the power of this unit is turned off. Select the position whose requirements your speaker system meets. IMPEDANCE SELECTOR REAR CENTER MAIN 6ΩMIN./SPEAKER SINGLE:6ΩMIN./SPEAKER DUAL:3ΩMIN./SPEAKER A OR B:4ΩMIN./SPEAKER A B:8ΩMIN./SPEAKER REAR CENTER MAIN 8ΩMIN./SPEAKER SINGLE:8ΩMIN./SPEAKER DUAL:4ΩMIN./SPEAKER A OR B:8ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER (U.S.A. model) (Upper position) Rear: The impedance of each speaker must be 6Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be 6Ω or higher. If you use two center speakers, the impedance of each speaker must be 3Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be 4Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher. (Lower position) Rear: The impedance of each speaker must be 8Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be 8Ω or higher. If you use two center speakers, the impedance of each speaker must be 4Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be 8Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
CENTER OUTPUT terminal
This terminal is for center channel line output.
There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
SUBWOOFER OUTPUT terminal
This terminal is for connecting with the input terminal of an
amplifier for driving a subwoofer.
This terminal outputs only frequencies below 200 Hz from the
main and center channels.
Note
Output level of signals from these terminals are adjusted
by the use of
VOLUME
control on the front panel or
VOLUME
keys on the remote control transmitter.
OUTPUT terminals (for driving speakers with external amplifiers)
Be sure to switch this only when the power of this unit is turned
off.
Select the position whose requirements your speaker system
meets.
(Upper position)
Rear:
The impedance of each speaker must be 6
Ω
or
higher.
Center:
If you use one center speaker, the impedance of the
speaker must be 6
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 3
Ω
or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 4
Ω
or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8
Ω
or higher.
(Lower position)
Rear:
The impedance of each speaker must be 8
Ω
or
higher.
Center:
If you use one center speaker, the impedance of the
speaker must be 8
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 4
Ω
or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 8
Ω
or higher.
<
Except Canada model
>
If you use two pairs of main speakers, the impedance
of each speaker must be 16
Ω
or higher.
IMPEDANCE SELECTOR switch
REAR
6
Ω
MIN./SPEAKER
SINGLE
:
6
Ω
MIN./SPEAKER
DUAL
:3
Ω
MIN./SPEAKER
A OR B
:4
Ω
MIN./SPEAKER
A
B
:8
Ω
MIN./SPEAKER
CENTER
MAIN
REAR
8
Ω
MIN./SPEAKER
SINGLE
:
8
Ω
MIN./SPEAKER
DUAL
:4
Ω
MIN./SPEAKER
A OR B
:8
Ω
MIN./SPEAKER
A
B
:
I6
Ω
MIN./SPEAKER
CENTER
MAIN
IMPEDANCE SELECTOR
CENTER
OUTPUT
SUB
WOOFER
(U.S.A. model)