Home » Yamaha Manuals » Audio Mixers » Yamaha V3.5 » Manual Viewer

Yamaha V3.5 DME Designer V3.5 Owners Manual - Page 48

Online, Making Communication Port Settings in DME Designer.

Get Yamaha V3.5 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Chapter 2 DME Designer Overview Online You can connect the DME or SP2060 unit to your computer and transfer configurations, scenes and parameters created in DME Designer into the DME or SP2060 unit. You can also read data from the DME or SP2060 unit into DME Designer, synchronizing it with the status of the DME or SP2060 unit. Because Synchronization presupposes that the DME or SP2060 unit can communicate with the computer where DME Designer is installed, the necessary drivers (USB-MIDI or DME-N Network Driver) must be installed, and appropriate settings must be made for each driver and for DME Designer communication port. NOTE Because there are no scene settings when the DME unit is purchased, the configuration and scene information created in DME Designer must first be transferred. NOTE A maximum of 32 device groups can be online. NOTE When combining DME64N/24N and DME Satellite units in a device group, be sure to assign a DME Satellite unit as the device group master. Synchronization cannot be performed if a DME64N/24N is assigned as the device group master. 1 DME Unit and Computer Connection. Connect the DME unit and computer using a USB cable or an Ethernet cable. See separate DME or SP2060 unit Owner's Manual for details. 2 Communication Driver Installation. Install the USB-MIDI driver or DME-N Network driver in the computer. See separate "DME Setup Manual" for details. 3 Communication Driver Setup. Make the necessary settings for the communication driver installed in the computer. If the driver is set up already, check the settings before going online. See separate "DME Setup Manual" for details. 4 Making Communication Port Settings in DME Designer. The port for each device group master can be selected via the "Communication Port" dialog box. If the driver is set up already, check the settings before going online. "Communication Port" dialog box (page 150) NOTE Slave DME64N/DME24N units connected via Ethernet and ICP1 units cannot be set. NOTE Only USB 1 can be selected for a DME Satellite unit connected via USB. 5 Storing and Checking Scenes. When moving online, the lowest scene must be stored. You can check if a scene is stored using the "Scene Manager" dialog box. NOTE Since the SP2060 has scene preset data this confirmation is not necessary. See "IP Address Setup" on page 160. 48 DME Designer Owner's Manual

Section	Page
The DME Audio System Network	3
The DME Designer Software Application	4
Data Handled by a DME Audio System	6
Changes from V3.0 to V3.5	18
Contents	19
Chapter 1 Before Using	21
Installing DME Designer	21
Starting DME Designer	21
Closing DME Designer	23
Chapter 2 DME Designer Overview	24
Names and Functions of the Windows	24
Users and Security	29
Files Used by the DME DESIGNER	32
Configuration Creation Procedure	47
Online	48
Chapter 3 Main Panel Window	52
Names and Functions of the Windows	52
Main Panel Window Menu	58
DME File Storage	68
Preferences	70
Event Logger	73
Scene Manager	80
User Control	87
Parameter Link	90
Synchronization (DME Designer and Unit Synchronization)	92
Event Scheduler	96
Wav File Manager	103
GPI	107
MIDI	120
User Defined Button (User Defined Parameters)	127
DAW Control	131
Remote Control Setup List	134
Internal HA Control	136
Parameter List	142
Component Lock	145
Scene Link Manager	146
SP2060 Library Manager	148
Communication Port Setup	150
Shortcut Keys	151
Security (Creating Users and Making User Settings)	152
Network Setup	160
Utility	162
Word Clock	169
Monitor Out	171
Clock	172
Language Settings	174
Backup	175
SP2060 Backup	176
DME Firmware Update	178
Device Information	181
Chapter 4 Designer	183
Editing Configurations	183
Designer Window	184
Toolkit Window	189
Designer Window Menu	194
Objects	201
Design Window Shared Settings and Operations	259
Drawing and Editing Wires	270
Adding, Deleting, and Renaming a Zone	281
Changing Device Groups	283
Adding, Deleting, and Renaming a Configuration	285
Area Window	287
Zone Window	288
Configuration Window	291
User Module	299
Chapter 5 Editor Window	309
Component Editor Window	309
User Control Editor/User Module Editor	315
Operation Mode and Design Mode	348
Context Menu	349
Snap	352
Library	354
Creating Parameter Links	358
Creating Component Links	360
Chapter 6 Component Guide	361
Types of Components	361
Ambient Noise Compensator	369
Audio Detector	371
Auto Gain Control	372
Crossover	373
Crossover Processor	377
Delay	389
Dynamics	392
Equalizer (EQ)	404
Fader	408
Feedback Suppressor	409
Filters	410
Meter	418
Miscellaneous	419
Mixer	421
Pan	443
Room Combiner	450
Router	451
Source Selector	453
Speaker Processor	454
SPX	461
Slot	472
Cascade (DME64N only)	474
Analog Input and Output	477
SP2060 Input and Output	479
CobraNet Input and Output	480
EtherSound Input and Output	482
MY-Card	483
Remote Controlled Head Amp	487
Component Glossary	489
Appendix	493
Options	493
Main Display	495
Parameter Edit Displays	496
Utility Displays	500
Troubleshooting	505

Match case Limit results 1 per page

Chapter 2

DME Designer Overview

DME Designer Owner’s Manual

Online

You can connect the DME or SP2060 unit to your computer and transfer conﬁgurations, scenes and

parameters created in DME Designer into the DME or SP2060 unit. You can also read data from the

DME or SP2060 unit into DME Designer, synchronizing it with the status of the DME or SP2060 unit.

Because Synchronization presupposes that the DME or SP2060 unit can communicate with the

computer where DME Designer is installed, the necessary drivers (USB-MIDI or DME-N Network

Driver) must be installed, and appropriate settings must be made for each driver and for DME

Designer communication port.

DME Unit and Computer Connection.

Connect the DME unit and computer using a USB cable or an Ethernet cable.

See separate DME or SP2060 unit Owner's Manual for details.

Communication Driver Installation.

Install the USB-MIDI driver or DME-N Network driver in the computer.

See separate “DME Setup Manual” for details.

Communication Driver Setup.

Make the necessary settings for the communication driver installed in the computer. If the driver is

set up already, check the settings before going online.

See separate “DME Setup Manual” for details.

Making Communication Port Settings in DME Designer.

The port for each device group master can be selected via the “Communication Port” dialog box. If

the driver is set up already, check the settings before going online.

“Communication Port” dialog box (

page 150

)

Storing and Checking Scenes.

When moving online, the lowest scene must be stored. You can check if a scene is stored using the

“Scene Manager” dialog box.

See “IP Address Setup” on

page 160

NOTE

Because there are no scene settings when the DME unit is purchased, the conﬁguration and scene information created in

DME Designer must ﬁrst be transferred.

NOTE

A maximum of 32 device groups can be online.

NOTE

When combining DME64N/24N and DME Satellite units in a device group, be sure to assign a DME Satellite unit as the

device group master. Synchronization cannot be performed if a DME64N/24N is assigned as the device group master.

NOTE

Slave DME64N/DME24N units connected via Ethernet and ICP1 units cannot be set.

NOTE

Only USB 1 can be selected for a DME Satellite unit connected via USB.

NOTE

Since the SP2060 has scene preset data this conﬁrmation is not necessary.