Yamaha YDP-S34 YDP-S34_Owners Manual_EN - Page 31

Keyboard Stand Assembly

Get Yamaha YDP-S34 PDF manuals and user guides View all Yamaha YDP-S34 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Keyboard Stand Assembly CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Assemble the unit on a hard and flat floor with ample space. • Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. • Be sure to tighten all screws upon completing assembly of the unit. • To disassemble, reverse the assembly sequence given below. Have a Phillips-head (+) screwdriver of the appropriate size ready. Remove all parts from the package and make sure you have all of the items. A Cord holder 1. Attach (finger-tighten) C to D and E. 1-1 Untie and straighten out the bundled pedal cord. Don't discard the vinyl tie. You will need it later in step 6. 1-2 Align D and E with each end of C. 1-3 Attach D and E to C by finger-tightening the long screws  (6 x 20 mm). 1-2 D C E D B E C Bundled pedal cord inside  6 x 25 mm long screws x 4  6 x 20 mm long screws x 2 AC adaptor x 1  6 x 16 mm short screws x 4  4 x 12 mm thin screws x 2  Caps x 2  4 x 20 mm tapping screws x 2  Anti-fall brackets x 2 * The two anti-fall brackets are identical. (Either one can be used for left or right.) * The adaptor may not be included, or may look different from the illustration above, depending on your particular area. Please check with your Yamaha dealer. 1-3 2. Attach B. Depending on the model of digital piano you purchased, the surface color of one side of B may be different from the other side. In this case, position B so that the side of the surface color similar to D and E faces the player. 2-1 Attach the top of B to D and E by finger- tightening the thin screws  (4 x 12 mm). 2-2 While pressing on the lower part of D and E from the outside, attach the anti-fall brackets  and then secure the bottom ends of B using four long screws  (6 x 25 mm). 2-3 Insert the other two tapping screws  (4 x 20 mm) into the other two screw holes to secure B. 2-4 Securely tighten the screws on the top of B that were attached in Step 2-1. 31 YDP-S34 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
31
YDP-S34 Owner’s Manual
Keyboard Stand Assembly
CAUTION
•
Be careful not to confuse parts, and be sure to install all
parts in the correct orientation. Please assemble the unit in
accordance with the sequence given below.
•
Assembly should be carried out by at least two persons.
•
Assemble the unit on a hard and flat floor with ample space.
•
Be sure to use the correct screw size, as indicated below.
Use of incorrect screws can cause damage.
•
Be sure to tighten all screws upon completing assembly of
the unit.
•
To disassemble, reverse the assembly sequence given
below.
Remove all parts from the package and make sure you
have all of the items.
*
The two anti-fall brackets are identical. (Either one can be used
for left or right.)
*
The adaptor may not be included, or may look different from the
illustration above, depending on your particular area. Please
check with your Yamaha dealer.
1.
Attach (finger-tighten) C to D and E.
1-1
Untie and straighten out the bundled pedal
cord.
Don’t discard the vinyl tie. You will need it later in
step 6.
1-2
Align D and E with each end of C.
1-3
Attach D and E to C by finger-tightening
the long screws
2
(6 x 20 mm).
2.
Attach B.
Depending on the model of digital piano you
purchased, the surface color of one side of B may
be different from the other side. In this case,
position B so that the side of the surface color
similar to D and E faces the player.
2-1
Attach the top of B to D and E by finger-
tightening the thin screws
4
(4 x 12 mm).
2-2
While pressing on the lower part of D and E
from the outside, attach the anti-fall
brackets
7
and then secure the bottom ends
of B using four long screws
1
(6 x 25 mm).
2-3
Insert the other two tapping screws
5
(4 x
20 mm) into the other two screw holes to
secure B.
2-4
Securely tighten the screws on the top of B
that were attached in Step 2-1.
Have a Phillips-head (+) screwdriver of the appropriate size
ready.
D
A
B
C
E
Bundled pedal cord inside
1
6 x 25 mm long screws x 4
6
Caps x 2
AC adaptor x 1
7
Anti-fall brackets x 2
2
6 x 20 mm long screws x 2
3
6 x 16 mm short screws x 4
4
4 x 12 mm thin screws x 2
5
4 x 20 mm tapping screws x 2
Cord holder
1-2
1-3
E
C
D