Yamaha YHT-24 Quick Connect Guide - Page 12
Operating The Universal Remote Control
View all Yamaha YHT-24 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
YHT-24 QUICK-CON N ECT GUIDE OPERATING THE UNIVERSAL REMOTE CONTROL OVERVIEW The universal remote control will control up to seven different types of components (including the HTR-5440 receiver), each of which becomes active when you press a selection (e.g., TV, VCR, etc.). We can only briefly describe some functions here, and we encourage you use the HTR-5440 Owner's Manual to gain additional experience with this powerful unit. PLAYING A VIDEOCASSETTE 1. Aim the remote control at the HTR-5440, press AMP/TUNER to select the component, and then press POWER to turn the receiver on. Press VCR (i.e., 6 on the keypad) as the input for the receiver. 2. Aim the remote control at the TV, press the TV to select the component, and then press POWER to turn the television on. Press TV INPUT (or A/B) to select the correct input. 3. Aim the remote control at the VCR, press VCR to select the component, and then press POWER to turn the VCR on. Put a tape in the VCR, press PLAY. NOTE: At this point, the VCR controls are assigned to the remote control, since VCR was the last selected component. If you now press the VOLUME up (down) buttons, the TV/VCR volume will be raised (or lowered). To adjust the receiver's volume, you must press AMP/TUNER to activate its functions. PLAYING A DVD 1. Aim the remote control at the HTR-5440, press AMP/ TUNER to select the component, and then press POWER to turn the receiver on. Press DVD/LD (i.e., 4 on the keypad) as the input for the receiver. 2. Press DVD/LD and then press POWER to turn the DVD (or LD) player on. NOTE: If the DVD player is plugged into the switched ac outlet (on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. 3. Load a DVD (or LD) into the DVD (or LD) player. 4. Aim the remote control at the DVD (or LD) player, and press > (forward button) to start play. NOTE: The DVD player's controls are now assigned to the remote control buttons, since DVD was the last selected component. RESETTING THE REMOTE CONTROL TO FACTORY CODES You can reset the remote control to factory codes for all components or a desired component, as follows: RESETTING CODES FOR ALL COMPONENTS 1. Press any component selector button other than AMP/TUNER. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 3. Using the keypad, enter the code "9990". 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. RESETTING CODES FOR A DESIRED COMPONENT 1. Press a component selector button that matches the component you wish to reset to factory codes. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 3. Using the keypad, enter the code "0000". 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. 5. For your convenience, the following reference chart lists the factory codes: Component Component Selector Button Code TV CBL/SAT VCR DVD/LD CD TAPE/MD TV Cable TV VCR DVD player CD player MD recorder 0101 0006 0002 0008 Yamaha 0005 Yamaha 0024 Yamaha ©2001 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (888) 435-7922 http://www.yamaha.com 12