Zanussi Z712W43BI User Manual - Page 32

Troubleshooting

Get Zanussi Z712W43BI PDF manuals and user guides View all Zanussi Z712W43BI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

4. Empty the drain pump. Refer to the emergency drain procedure. 5. When the drain pump is empty, install the inlet hose again. TROUBLESHOOTING WARNING! Make sure that the temperature is higher than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. WARNING! Refer to Safety chapters. INTRODUCTION The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. WARNING! Deactivate the appliance before carrying out any check. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The mains supply is unstable. Wait until the mains supply is stable. • - No communication between electronic elements of the appliance. Switch it off and switch on again. The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. • - The appliance does not fill with water properly. After the proper check, start the appliance again by pressing Start/Pause button the appliance tries to resume the cycle . If the error persists the alarm code will appear again. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. Please check the door! If the appliance is overloaded, remove some items from the drum and/or hold the door shut while touching the Start/Pause picture below). button until the indicator stops flashing (see the 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
4.
Empty the drain pump. Refer to the emergency
drain procedure.
5.
When the drain pump is empty, install the inlet
hose again.
WARNING!
Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised
Service Centre.
WARNING!
Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an alarm code and
the
Start/Pause
button may flash continuously:
•
- The mains supply is unstable. Wait until the mains supply is stable.
•
- No communication between electronic elements of the appliance. Switch it off and switch on
again. The programme was not finished properly or the appliance stopped too early. If the alarm code
appears again, contact the Authorised Service Centre.
•
- The appliance does not fill with water properly. After the proper check, start the appliance
again by pressing Start/Pause
button the appliance tries to resume the cycle . If the error persists
the alarm code will appear again.
•
- The appliance does not drain the water.
•
- The appliance door is open or not closed correctly. Please check the door!
If the appliance is overloaded, remove some items from the drum and/or hold the door shut
while touching the Start/Pause
button until the indicator
stops flashing (see the
picture below).
32