Zanussi ZBB28441SA Product Manaul - Page 9

Warning, Important - manual

Page 9 highlights

What to do if... Warning! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. Important! There are some sounds during normal use (compressor, refrigerant circulation). Problem Possible cause Solution The appliance does not operate. The lamp does not operate. The appliance is switched off. Switch on the appliance. The mains plug is not connected to Connect the mains plug to the mains the mains socket correctly. socket correctly. The appliance has no power. There Connect a different electrical appliis no voltage in the mains socket. ance to the mains socket. Contact a qualified electrician. The lamp does not work. The lamp is in stand-by. Close and open the door. The lamp is defective. Refer to "Replacing the lamp". The compressor operates The temperature is not set correct- Set a higher temperature. continually. ly. The door is not closed correctly. Refer to "Closing the door". The door has been opened too fre- Do not keep the door open longer quently. than necessary. The product temperature is too high. Let the product temperature decrease to room temperature before storage. The room temperature is too high. Decrease the room temperature. Water flows on the rear plate of the refrigerator. During the automatic defrosting process, frost defrosts on the rear plate. This is correct. Water flows into the refrig- The water outlet is clogged. erator. Clean the water outlet. Products prevent that water flows Make sure that products do not into the water collector. touch the rear plate. Water flows on the ground. The melting water outlet does not flow in the evaporative tray above the compressor. Attach the melting water outlet to the evaporative tray. The temperature in the ap- The temperature regulator is not set Set a higher/lower temperature. pliance is too low/high. correctly. The temperature in the re- There is no cold air circulation in frigerator is too high. the appliance. Make sure that there is cold air circulation in the appliance. The temperature in the freezer is too high. Products are too near to each oth- Store products so that there is cold er. air circulation. www.zanussi.com 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

What to do if…
Warning!
Before troubleshooting,
disconnect the mains plug from the mains
socket.
Only a qualified electrician or competent
person must do the troubleshooting that is not
in this manual.
Important!
There are some sounds during
normal use (compressor, refrigerant
circulation).
Problem
Possible cause
Solution
The appliance does not
operate. The lamp does
not operate.
The appliance is switched off.
Switch on the appliance.
The mains plug is not connected to
the mains socket correctly.
Connect the mains plug to the mains
socket correctly.
The appliance has no power. There
is no voltage in the mains socket.
Connect a different electrical appli-
ance to the mains socket.
Contact a qualified electrician.
The lamp does not work.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Refer to "Replacing the lamp".
The compressor operates
continually.
The temperature is not set correct-
ly.
Set a higher temperature.
The door is not closed correctly.
Refer to "Closing the door".
The door has been opened too fre-
quently.
Do not keep the door open longer
than necessary.
The product temperature is too
high.
Let the product temperature de-
crease to room temperature before
storage.
The room temperature is too high.
Decrease the room temperature.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting
process, frost defrosts on the rear
plate.
This is correct.
Water flows into the refrig-
erator.
The water outlet is clogged.
Clean the water outlet.
Products prevent that water flows
into the water collector.
Make sure that products do not
touch the rear plate.
Water flows on the ground.
The melting water outlet does not
flow in the evaporative tray above
the compressor.
Attach the melting water outlet to the
evaporative tray.
The temperature in the ap-
pliance is too low/high.
The temperature regulator is not set
correctly.
Set a higher/lower temperature.
The temperature in the re-
frigerator is too high.
There is no cold air circulation in
the appliance.
Make sure that there is cold air circu-
lation in the appliance.
The temperature in the
freezer is too high.
Products are too near to each oth-
er.
Store products so that there is cold
air circulation.
9
www.zanussi.com