Home » ZyXEL Manuals » Wireless » ZyXEL WX3310-B0 » Manual Viewer

ZyXEL WX3310-B0 User Guide - Page 12

Introduction, WX3310-B0 User's Guide, Front Panel, The following table describes the LEDs

Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Figure 4 Front Panel Chapter 1 Introduction The following table describes the LEDs Table 1 Front Panel LEDs LED COLOR STATUS WPS Green Blinking Red On Blinking AP Mode Link Quality (wired connection) Green Off On Blinking Off DESCRIPTION WPS process in progress WPS failed. Overlapping WPS processes (two wireless clients are trying to simultaneously connect to the WX3310). Wait for the LED to go off, then initiate WPS again. No WPS activity. Connected to the modem/router. Connected, but not synced with the Zyxel MPro Mesh gateway (router controller). There is no connection to the modem/router. WX3310-B0 User's Guide 12

Section	Page
WX3310-B0	1
Document Conventions	3
Contents Overview	4
Table of Contents	5
User’s Guide	9
Introduction	10
1.1 Overview	10
1.2 Dual-Band WiFi	10
1.3 Securing the WX3310	11
1.4 Front Panel and LEDs	11
1.5 Back Panel	13
1.6 The WPS Button	14
1.6.1 Using the WPS Button	14
1.7 The RESET Button	15
1.7.1 Using the RESET Button	15
The Web Configurator	16
2.1 Overview	16
2.1.1 What You Can Do in this Chapter	16
2.2 Accessing the Web Configurator	16
2.3 Preparing your Computer to Access the Web Configurator	18
2.3.1 Static IP Configuration in Microsoft Windows	19
2.3.2 Static IP Configuration in MAC OS X	21
Modes	24
3.1 Overview	24
3.1.1 Web Configurator Modes	24
3.1.2 Device Operating Modes	24
Easy Mode	26
4.1 Overview	26
4.1.1 What You Can Do in this Chapter	27
4.2 Navigation Panel	27
4.3 Network Map	28
4.4 Status Screen (Easy Mode)	28
Access Point Mode	31
5.1 Overview	31
5.1.1 What You Can Do in this Chapter	31
5.2 Setting your WX3310 to AP Mode	31
5.2.1 Status Screen (AP Mode)	32
5.2.2 AP Navigation Panel	34
Repeater Mode	36
6.1 Overview	36
6.1.1 What You Can Do in this Chapter	36
6.2 Setting your WX3310 to Repeater Mode	36
6.2.1 Status Screen (Repeater Mode)	37
6.2.2 Repeater Navigation Panel	39
Tutorials	41
7.1 Overview	41
7.2 Configuring the WX3310 as an Access Point	41
7.3 Configuring the WX3310 as a Repeater	41
7.3.1 Selecting an AP from an Automatically Detected List	41
7.3.2 Selecting an AP by Manually Entering Security Information	42
Technical Reference	44
Monitor	45
8.1 Overview	45
8.2 What You Can Do	45
8.3 Log	45
8.4 Wireless Monitor	46
8.5 MBSS Monitor	48
8.6 Multicast Monitor	50
Network	51
9.1 Overview	51
9.2 What You Can Do	51
9.3 What You Need To Know	51
9.4 Networking Screen	52
Wireless LAN	54
10.1 Overview	54
10.2 What You Can Do in this Chapter	55
10.3 What You Should Know	55
10.3.1 Wireless Basic	55
10.3.2 WiFi6 / IEEE 802.11ax	55
10.4 Basic Wireless Network Screen	56
10.5 Advanced Wireless Network Screen	57
10.6 WPS Screen	58
10.7 MAC Filter	59
10.8 MBSS Screen	60
10.9 Technical Reference	61
10.9.1 Wireless Network Overview	61
10.9.2 Wireless Security Overview	63
10.9.3 WiFi Protected Setup (WPS)	66
AP Connection (Repeater Mode)	75
11.1 Overview	75
11.2 What You Can Do in this Chapter	75
11.3 Station Screen	75
11.4 AP List Screen	76
11.5 WPS Screen	78
Mesh	79
12.1 Overview	79
12.2 Mesh Screen	80
Maintenance	81
13.1 Overview	81
13.2 What You Can Do in this Chapter	81
13.3 Password Screen	81
13.4 Time Screen	82
13.5 Firmware Upgrade Screen	83
13.6 Restore Screen	84
13.6.1 Backup Configuration	85
13.6.2 Restore Configuration	85
13.6.3 Back to Factory Defaults	85
13.7 Restart Screen	86
Troubleshooting	87
14.1 Power, Hardware Connections, and LEDs	87
14.2 WX3310 Access and Login	88
14.3 Internet Access	89
14.4 Resetting the WX3310 to Its Factory Defaults	90
14.5 Wireless Problems	90
Wireless LANs	91
Customer Support	103
Legal Information	109