Home » Acer Manuals » Servers » Acer AB2x280 F1 » Manual Viewer

Acer AB2x280 F1 Acer AB7000 Enclosure with AB2x280 F1 and AB460 F1 Blade Serve - Page 46

Removing/Replacing the blade cover, cover toward the front of the blade to lock it into place.

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Removing/Replacing the blade cover 1. Remove the blade unit from the enclosure (see "Removing the blade unit" above). 2. Depress the two buttons on the cover while pushing the cover toward the rear of the blade unit. When it stops, lift the cover off the blade unit. 3. To replace the cover, fit the six grooves in the cover into the studs in the sides of the blade, then slide the cover toward the front of the blade to lock it into place. 38 Chapter 6

Section	Page
Preface	2
Revision History	2
Copyright	2
Disclaimer	2
Conventions	3
Safety, Care and Regulatory Information	4
Preventing electrostatic discharge	4
Server warnings and cautions	4
System components	9
Blade unit components	9
Exploded view of AB460 F1 blade module	9
Exploded view of AB2x280 F1 blade module	10
System parts list	11
Removal and replacement procedures	17
Extend the server from the rack	18
Power down the server	20
Remove the server from the rack	20
System specifications	21
Hardware specifications	21
Server specification	21
AB460 F1 blade specifications	21
ABx2 280 F1 blade specifications	22
Environmental specifications	22
Mechanical specifications	23
System appearance	25
Front panel	25
Front panel LED indicators	25
Blade control panel	26
Rear panel	28
Rear modules	28
Chassis Management Module	29
Acer 4X QDR InfiniBand switch module	30
Acer 4X QDR InfiniBand switch module with integrated CMM	31
InfiniBand switch LEDs	31
System block diagram	32
AB460 F1 mainboard block diagram	32
Mainboard	35
AB460 F1 mainboard connectors	35
Jumpers	36
Clearing CMOS	36
AB2x280 F1 mainboard connectors	37
Jumpers	38
Clearing CMOS	38
Hardware removal and installation	39
Power supply removal and installation	39
Removing a Power Supply	39
Installing a Power Supply	40
Switch module removal and installation	41
Removing a Switch Module	41
Installing a Switch Module	41
Removing and installing the hard disk	42
AB460 F1 Hard Disk Drives	42
AB2x280 F1 Hard Disk Drives	42
Removing a hard drive carrier	43
Installing a Hard Drive	43
Blade unit removal and installation	44
Removing the blade unit	44
Installing a Blade Unit	45
Removing/Replacing the blade cover	46
AB460 F1 Memory removal and installation	47
Memory Support	47
Installing DIMM Memory Modules	47
Populating Memory Slots	47
AB2x280 F1 Memory removal and installation	53
Memory Support	53
Memory Installation	53
Populating Memory Slots	53
Supported Memory Population	54
Heatsink removal and installation	57
Removing the heatsink	57
Installing the heatsink	57
Processor removal and installation	58
Removing a processor	58
Installing a Processor	58
Infiniband mezzanine card installation	59
Card installation	59
Rackmount installation procedure	60
Rack Mounting Hardware	60
Installation	60
System Check Procedures	63
AMI BIOS Recovery	64
BIOS Updates	64
Flashing BIOS	64
Flashing a BIOS using the USB Ports on the CMM	64
Flashing a BIOS using a Floppy Image File	64
BIOS Setup	65
Changing configuration data	65
Main setup	66
Advanced Settings	67
Boot Features	67
Power configuration	68
Processor & Clock Options	68
Advanced Chipset Control	70
CPU Bridge configuration	70
North Bridge configuration	71
South Bridge configuration	72
IDE/SATA configuration	73
PCI/PnP configuration	74
Super IO Device configuration	75
ACPI configuration	75
Security	77
System Management Settings	78
System Information	78
IP Address	79
Remote Access Configuration	79
Event Log Configuration	80
Boot	81
Boot Device Priority	81
Hard Disk Drives	82
Removable Drives	82
CD/DVD Drive	83
Network Drives	83
Exit Options	84
BIOS POST Messages	85
BIOS POST Codes	88
Recoverable POST Errors	88
Terminal POST Errors	88

We apologize, but we cannot currently deliver this PDF manual by request of the manufacturer.

We apologize for any inconveniece.