Alpine CDA-9886 User Manual - Page 35

3 Press SOURCE/ to adjust the slope. Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/oct. * FLAT can be set for the HIGH slope only when User's is selected in "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 31). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With this unit, a message is displayed when the response slope for the high range speaker is set to FLAT. 4 Turn the Rotary encoder to adjust the output level. Adjustable output level: -12 to 0 dB. 5 Repeat steps 1 to 4 to make adjustment to the other bands. 4.2ch (FRONT/REAR/SUBW.) System 1 After selecting X-Over from the Sound Field Adjustment mode, press BAND to select the band to be adjusted. 4.2ch (FRONT/REAR/SUBW.) System / NORMAL (L=R) Setting items: LOW (SUB-W) / MID (REAR) / HIGH (FRONT) 4.2ch (FRONT/REAR/SUBW.) System / INDIVIDUAL (L/R) Setting items: LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L / MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R 2 Press or to select the desired cut-off frequency (Crossover Point). Adjustable frequency bands: 4.2ch (FRONT/REAR/SUBW.) System Setting items: 20 Hz~200 Hz 3 Press SOURCE/ to adjust the slope. Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/oct. 4 Turn the Rotary encoder to adjust the output level. Adjustable output level: -12 to 0 dB. 5 Repeat steps 1 to 4 to make adjustment to the other bands. • While adjusting the X-over, you should consider the frequency response of the connected speakers. • About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer to the Owner's Manual of PXA-H100. Storing the Sound Field Adjustment Settings The Sound Field Adjustment Settings containing Parametric EQ/ Graphic EQ Adjustment, Time Correction and X-Over settings can be stored in the preset memory. 1 When the settings of Sound Field Adjustment have been completed, select any one of the preset buttons (1 through 6) in any item of the Sound Field adjustment mode (e.g. X-Over), press and hold the desired preset buttons for at least 2 seconds. 2 Turn the Rotary encoder to select PROTECT YES/NO, and then press /ENT to store the adjusted contents. PROTECT YES (Initial setting) PROTECT NO • If YES is selected, the adjusted contents are protected and stored into the preset buttons. When you want to store the parameter into a protected preset button, "Replace NO/YES" can be selected. • If NO is selected, the preset is stored. • While perform this operation, all adjusted contents of Parametric EQ/Graphic EQ, Time Correction and X-Over will be stored in the preset buttons. • The stored contents are not deleted even when resetting the unit or disconnecting the battery. • The stored contents can be recalled by performing operation in "Recalling the Stored Sound Field Adjustment Settings" (page 33). Recalling the Stored Sound Field Adjustment Settings The stored Sound Field Settings contain Parametric EQ/Graphic EQ Adjustment, Time Correction and X-Over settings that are stored in the preset memory. 1 After selecting any item of the Sound Field Adjustment mode (e.g. X-Over), press any one of the preset buttons (1 through 6) that has your desired characteristic in memory to recall the stored settings. 2 Press the preset buttons again to return to the Sound Field Adjustment mode. • While performing this operation, all adjustment contents of Parametric EQ/Graphic EQ, Time Correction and X-Over stored in the preset buttons will be recalled. 33-EN