Alpine CDE-SXM145BT User Manual - Page 43

Installation, Mounting the Microphone

Get Alpine CDE-SXM145BT PDF manuals and user guides View all Alpine CDE-SXM145BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Installation CAUTION When you install this unit in your car, do not remove the detachable front panel. If the detachable front panel is removed during installation, you might press too hard and warp the metal plate that holds it in place. The main unit must be mounted within 35 degrees of the horizontal plane, back to front. Detachable Front Panel Note • For the screw marked "*", use an appropriate screw for the chosen mounting location. 3 Slide the CDE-SXM145BT/CDE-143BT/UTE-42BT into the dashboard until it clicks. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the detachable front panel. Removal 1 Remove the detachable front panel. 2 Insert the bracket keys into the unit, along the guides on either side. The unit can now be removed from the mounting sleeve. This unit Less than 35° Bracket keys (Included) 1 Remove the mounting sleeve from the main unit (Refer to "Removal" on page 43). Mounting Sleeve (Included) Dashboard 3 Pull the unit out, keeping it unlocked as you do so. JAPANESE CAR Front Frame This unit Screws (M5 × 8) (Included) Pressure Plates* This unit * If the installed mounting sleeve is loose in the dashboard, the pressure plates may be bent slightly to remedy the problem. 2 Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot. Connect each input lead coming from an amplifier to the corresponding output lead coming from the left rear of the CDE-SXM145BT/CDE-143BT/UTE-42BT. Connect all other leads of the CDE-SXM145BT/CDE-143BT/UTE-42BT according to details described in the CONNECTIONS section. Hex Nut (M5) Screw * Bolt Stud Mounting Bracket Mounting the Microphone For the sake of safety, mount the microphone in the following location. • In a stable and secure location. • In a location that does not inhibit safely driving the vehicle. • Mount the microphone in a location where the driver's voice can easily be picked up. Choose a location for the microphone that can easily pick up the drivers voice. Requiring the driver to move towards the microphone for audibility causes a distraction that could be dangerous. Metal Mounting Strap This unit 43-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
43
-EN
Installation
CAUTION
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
The main unit must be mounted within 35 degrees of the
horizontal plane, back to front.
1
Remove the mounting sleeve from the main unit (Refer to
“Removal” on page 43).
*
If the installed mounting sleeve is loose in the dashboard, the
pressure plates may be bent slightly to remedy the problem.
2
Reinforce the head unit with the metal mounting strap
(not supplied). Secure the ground lead of the unit to a
clean metal spot.
Connect each input lead coming from an amplifier to the
corresponding output lead coming from the left rear of the
CDE-SXM145BT/CDE-143BT/UTE-42BT. Connect all other leads
of the CDE-SXM145BT/CDE-143BT/UTE-42BT according to
details described in the CONNECTIONS section.
Note
•
For the screw marked “
*
”, use an appropriate screw for the chosen
mounting location.
3
Slide the CDE-SXM145BT/CDE-143BT/UTE-42BT into the
dashboard until it clicks. This ensures that the unit is
properly locked and will not accidentally come out from
the dashboard. Install the detachable front panel.
1
Remove the detachable front panel.
2
Insert the bracket keys into the unit, along the guides on
either side. The unit can now be removed from the
mounting sleeve.
3
Pull the unit out, keeping it unlocked as you do so.
JAPANESE CAR
Mounting the Microphone
For the sake of safety, mount the microphone in the following location.
•
In a stable and secure location.
•
In a location that does not inhibit safely driving the vehicle.
•
Mount the microphone in a location where the driver’s voice can
easily be picked up.
Choose a location for the microphone that can easily pick up the drivers
voice. Requiring the driver to move towards the microphone for
audibility causes a distraction that could be dangerous.
Detachable Front
Panel
Less than 35°
Dashboard
Mounting Sleeve (Included)
Pressure Plates
*
This unit
*
Bolt Stud
Hex Nut (M5)
Metal
Mounting
Strap
Screw
This unit
Removal
Bracket keys
(Included)
This unit
Front Frame
Screws (M5 × 8)
(Included)
This unit
Mounting Bracket