Alpine IDA-X303 Ida-x303 Owner's Manual (english) - Page 20

Sound Setting Double Action encoder IMPRINT /ENTER PRESET Adjusting Subwoofer/Bass/Treble/ Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/ Defeat 1 Press IMPRINT repeatedly to choose the desired mode. Each press changes the mode as follows: SUBW LV*1 FADER LV*2 SUBW LV*1 BASS LV LOUD*3 TREBLE LV BALANCE LV DEFEAT VOLUME Subwoofer: +0 ~ +15 Bass level: -7 ~ +7 Treble level: -7 ~ +7 Balance: -15 ~ +15 Fader: -15 ~ +15 Loudness : ON/OFF Defeat : ON/OFF Volume: 0 ~ 35 • If IMPRINT is not pressed within 5 seconds after selecting the Subwoofer, Bass, Treble, Balance or Fader mode, the unit automatically returns to normal mode. • Loudness introduces a special low-and high-frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound. The function is inoperable when DEFEAT is set to ON. *1 When the subwoofer mode is set to OFF, its level cannot be adjusted. *2 If you set the 4.2ch (FRONT/REAR/SUBW.)/2.2ch (3WAY) switch of the IMPRINT audio processor (PXA-H100) to 2.2ch (3WAY), you cannot adjust the FADER mode. For details, refer to the Owner's Manual of PXA-H100. *3 When an external audio processor is connected, this setting cannot be made. 2 Turn the Double Action encoder until the desired sound is obtained in each mode. • Depending on the connected devices, some functions and display indications do not work. Turning Subwoofer ON/OFF When the subwoofer is on, you can adjust the subwoofer output level (refer to page 18). For this unit, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected. 1 Press and hold IMPRINT for at least 2 seconds to activate the AUDIO selection mode. 2 Turn the Double Action encoder to select the SUBW mode, and then press /ENTER. SUBW SUBW SYSTEM* BASS TREBLE HPF SUBW * Displayed only when subwoofer is ON. 3 Turn the Double Action encoder to select SUBW ON/OFF, and then press /ENTER. ON OFF 4 Press to return to normal mode. • If no operation is performed for 15 seconds, the unit will return to normal mode automatically. • If is pressed during setting, the unit returns to the previous item. Setting the Subwoofer System When the subwoofer is on, you can select either SYS 1 or SYS 2 for the desired subwoofer effect. For this unit, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected. 1 Press and hold IMPRINT for at least 2 seconds to activate the AUDIO selection mode. 2 Turn the Double Action encoder to select the SUBW SYSTEM mode, and then press /ENTER. SUBW SUBW SYSTEM* BASS TREBLE HPF SUBW * Displayed only when subwoofer is ON. 3 Turn the Double Action encoder to select the SUBW SYS 1 or SUBW SYS 2, and then press /ENTER. SYS 1 SYS 2 SYS 1 : SYS 2 : 4 Press Subwoofer level changes according to the main volume setting. Subwoofer level change is different from the main volume setting. For example, even at low volume settings, the subwoofer is still audible. to return to normal mode. • If no operation is performed for 15 seconds, the unit will return to normal mode automatically. • If is pressed during setting, the unit returns to the previous item. • This function is inoperable when Subwoofer is set to OFF. 18-EN