Alpine INE-W960 Owner's Manual (english) - Page 38
Adjusting the Crossover Settings (X-Over), Adjusting the Parametric Equalizer Curve (Parametric EQ)
View all Alpine INE-W960 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 38 highlights
Adjusting the Crossover Settings (XOver) [X-Over] is selected on the Sound setup menu in step 3. Refer to "Sound Setup Operation" (page 34). Before performing the following procedures, refer to "About the Crossover" (page 41). Setting item: X-Over 1 Touch [Channel] to select the channel. Each time you touch, the channel switches. Adjusting the Parametric Equalizer Curve (Parametric EQ) [Parametric EQ] is selected on the Sound setup menu in step 3. Refer to "Sound Setup Operation" (page 34). You can modify the Equalizer settings to create a response curve more appealing to your personal taste. Setting item: Parametric EQ 1 Adjust the Parametric EQ to your preference. • The channel being adjusted is displayed in red. Front HPF Rear HPF SubW. LPF 2 Adjust the crossover to your preference. Selecting the Cut-Off Frequency Touch [ ] or [ ] of "Freq.", then select the cut-off frequency. Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 / 160 / 200 Hz Adjusting the Slope Touch [ ] or [ ] of "Slope", then adjust the HPF or LPF slope. Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct Adjusting the Level Touch [ ] or [ ] of "Level", then adjust the HPF or LPF level. Setting contents: -12 to 0 dB (Initial setting: 0) 3 Repeat steps 1 to 2 to make adjustment to the other channels. 4 To store the adjusted setting value, touch and hold [Preset1], [Preset2], or [Preset3] for at least 2 seconds. • Touch [Flat] to initialize all values. • If the Rear Speaker setting is "Off," the Rear Speaker setting cannot be edited (Refer to page 39). • If the Subwoofer setting is "Off," the Subwoofer setting cannot be edited (Refer to page 39). • While adjusting the X-Over you should consider the frequency response of the connected speakers. Calling the X-Over adjusted value Calling the pre-set X-Over adjusted value. Touch [Preset1], [Preset2], or [Preset3] on the XOver screen. The setting stored in the Preset will be recalled. 38-EN Adjusting the Band Touch [Band] to select the band to be adjusted. Band1 Band2 ··· Band8 Band9 • You can select a band directly by touching the screen. Adjusting the Frequency Touch [ ] or [ ] of "Freq." to adjust the frequency of the selected band. Adjustable frequency Bands: 20 Hz to 20 kHz (in 1/3 octave steps) Band1: 20 Hz~100 Hz (63 Hz) Band2: 63 Hz~315 Hz (125 Hz) Band3: 125 Hz~500Hz (250 Hz) Band4: 250 Hz~1 kHz (500Hz) Band5: 500 Hz~2 kHz (1 kHz) Band6: 1 kHz~4 kHz (2 kHz) Band7: 2 kHz~7.2 kHz (4 kHz) Band8: 5.8 kHz~12 kHz (8 kHz) Band9: 9 kHz~20 kHz (16 kHz) Adjusting the Level Touch [ ] or [ ] of "Level" to adjust the level of selected band. Setting contents: -7 to +7 (Initial setting: 0) Setting the Bandwidth Touch [ ] or [ ] of "Q Adjust" to select the bandwidth. Setting contents: 1 (Initial setting) / 2 / 3 2 To adjust another band, repeat step 1, and adjust all bands. 3 To store the adjusted setting value, touch and hold [Preset1], [Preset2], or [Preset3] for at least 2 seconds.