Asus M2N68-AM SE User Manual - Page 37

IDE Configuration

Get Asus M2N68-AM SE PDF manuals and user guides View all Asus M2N68-AM SE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2.3.3 IDE Configuration The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press if you want to configure the item. Onboard IDE Controller [Enabled] Enables or disables the onboard IDE controller. Configuration options: [Disabled] [Enabled] Serial ATA Devices [Enabled] Enables or disables the Serial ATA devices. Configuration options: [Enabled] [Disabled] SATA Mode Select [SATA Mode] Selects the SATA mode. Configuration options: [SATA Mode] 2.3.4 Primary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate submenu for each IDE device. Select a device item then press to display the IDE device information. The BIOS automatically detects the values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These values are not user-configurable. These items show Not Detected if no IDE device is installed in the system. Type [Auto] Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the appropriate IDE device type. Select [CDROM] if you are specifically configuring a CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Configuration options: [Not Installed] [Auto] [CDROM] [ARMD] LBA/Large Mode [Auto] Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto] Block (Multi-Sector Transfer) M [Auto] Enables or disables data multi-sectors transfers. When set to [Auto], the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled] [Auto] PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Enabled] Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled] Chapter 2: BIOS information 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 2: BIOS information
2-5
2.3.3
IDE Configuration
The items in this menu allow you to set or change the configurations for the IDE devices
installed in the system. Select an item then press
<Enter>
if you want to configure the item.
Onboard IDE Controller [Enabled]
Enables or disables the onboard IDE controller. Configuration options: [Disabled] [Enabled]
Serial ATA Devices [Enabled]
Enables or disables the Serial ATA devices. Configuration options: [Enabled] [Disabled]
SATA Mode Select [SATA Mode]
Selects the SATA mode. Configuration options: [SATA Mode]
2.3.4
Primary IDE Master/Slave
While entering Setup, the BIOS automatically detects the presence of IDE devices. There is
a separate submenu for each IDE device. Select a device item then press
<Enter>
to display
the IDE device information.
The BIOS automatically detects the values opposite the dimmed items (Device, Vendor,
Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring).
These values are not user-configurable. These items show
Not Detected
if no IDE device is
installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to
[Auto
] allows automatic selection of the appropriate
IDE device type. Select
[CDROM]
if you are specifically configuring a CD-ROM drive. Select
[ARMD]
(ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to
[Auto]
enables the LBA mode if the device
supports this mode, and if the device was not previously formatted with LBA mode disabled.
Configuration options: [Disabled] [Auto]
Block (Multi-Sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to
[Auto]
, the data transfer from
and to the device occurs multiple sectors at a time if the device supports multi-sector transfer
feature. When set to
[Disabled]
, the data transfer from and to the device occurs one sector
at a time. Configuration options: [Disabled] [Auto]
PIO Mode [Auto]
Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled]