Asus P4T-E Motherboard DIY Troubleshooting Guide - Page 22

ASUS P4T-E User's Manual, USB2 / CNRUSB Selection J3-J3+, OC3, Onboard Audio Setting ADN audio - p4t motherboard

Get Asus P4T-E PDF manuals and user guides View all Asus P4T-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

3. H/W SETUP Motherboard Settings 3. HARDWARE SETUP 5) Onboard Audio Setting (ADN) (audio models only) The onboard Audio Codec may be enabled or disabled using these jumpers. Disable the onboard Audio Codec if using a PCI audio card on any of the expansion slots or a primary audio/modem CNR on a CNR slot (see CNR Slot later in this section). Setting Enable Disable ADN [1-2] (default) [2-3] P4T-E P4T-E AUDIO Setting ADN 2 1 ENABLE AUDIO (Default) 3 2 DISABLE AUDIO 6) USB2 / CNRUSB Selection (J3-J3+, OC3) The CNR slot can support an optional USB hub CNR card. Three jumpers are used to control selection of USB or CNR functions: J3-, J3+ and OC3. The factory default setting is for standard USB2 control. If a USB hub CNR card is used, reset these jumpers to CNRUSB setting shown below. IMPORTANT! Always set all three jumpers accordingly when selecting a device. P4T-E P4T-E CNR/USB Selection 12 OC3 12 J3J3+ USB2 (Default) 23 OC3 23 J3J3+ CNRUSB 22 ASUS P4T-E User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
22
ASUS P4T-E User’s Manual
3. HARDWARE SETUP
Motherboard Settings
3. H/W SETUP
P4T-E
P4T-E AUDIO Setting
ENABLE AUDIO
(Default)
DISABLE AUDIO
ADN
2
3
1
2
P4T-E
P4T-E CNR/USB Selection
USB2
(Default)
CNRUSB
12
J3-
J3+
2
3
J3-
J3+
12
OC3
23
OC3
6)
USB2 / CNRUSB Selection (J3-J3+, OC3)
The CNR slot can support an optional USB hub CNR card.
Three jumpers are
used to control selection of USB or CNR functions:
J3-
,
J3+
and
OC3
.
The
factory default setting is for standard USB2 control.
If a USB hub CNR card is
used, reset these jumpers to CNRUSB setting shown below.
IMPORTANT!
Always set all three jumpers accordingly when selecting a device.
5)
Onboard Audio Setting (ADN) (audio models only)
The onboard Audio Codec may be enabled or disabled using these jumpers.
Disable the onboard Audio Codec if using a PCI audio card on any of the
expansion slots or a primary audio/modem CNR on a CNR slot (see CNR Slot
later in this section).
Setting
ADN
Enable
[1-2] (default)
Disable
[2-3]