Asus ROG MAXIMUS XI GENE Users Manual English - Page 82

PCH Storage Configuration, SATA Controllers, SATA Mode Selection, SMART Self Test

Get Asus ROG MAXIMUS XI GENE PDF manuals and user guides View all Asus ROG MAXIMUS XI GENE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

3.6.5 PCH Storage Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. SATA Controller(s) This item allows you to enable or disable the SATA Device. Configuration options: [Enabled] [Disabled] The following items appear only when SATA Controller(s) is set to [Enabled]. SATA Mode Selection This item allows you to set the SATA configuration. [AHCI] [Intel RST Premium With Intel Optane System Acceleration(RAID)] Set to [AHCI] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Set to [Intel RST Premium With Intel Optane System Acceleration(RAID)] when you want to create a RAID configuration from the SATA hard disk drives. SMART Self Test SMART (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system that shows a warning message during POST (Power-on Self Test) when an error occurs in the hard disks. Configuration options: [On] [Off] SATA6G_1(Black) - SATA6G_4(Black) SATA6G_1(Black) - SATA6G_4(Black) This item allows you to enable or disable the selected SATA port. Configuration options: [Disabled] [Enabled] Hot Plug These items appears only when the SATA Mode Selection is set to [AHCI] and allows you to enable or disable SATA Hot Plug Support. Configuration options: [Disabled] [Enabled] 3.6.6 PCH-FW Configuration This item allows you to configure the firmware TPM. Chapter 3 3-18 Chapter 3: BIOS Setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
3-18
Chapter 3: BIOS Setup
Chapter 3
3.6.5
PCH Storage Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show
Not Present
if no SATA device is installed to the corresponding SATA
port.
SATA Controller(s)
This item allows you to enable or disable the SATA Device.
Configuration options: [Enabled] [Disabled]
The following items appear only when
SATA Controller(s)
is set to
[Enabled]
.
SATA Mode Selection
This item allows you to set the SATA configuration.
[AHCI]
Set to [AHCI] when you want the SATA hard disk drives to
use the AHCI (Advanced Host Controller Interface). The
AHCI allows the onboard storage driver to enable advanced
Serial ATA features that increases storage performance
on random workloads by allowing the drive to internally
optimize the order of commands.
[Intel RST Premium With
Intel Optane System
Acceleration(RAID)]
Set to [Intel RST Premium With Intel Optane System
Acceleration(RAID)] when you want to create a RAID
configuration from the SATA hard disk drives.
SMART Self Test
SMART (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system that
shows a warning message during POST (Power-on Self Test) when an error occurs in the
hard disks.
Configuration options: [On] [Off]
SATA6G_1(Black) - SATA6G_4(Black)
SATA6G_1(Black) - SATA6G_4(Black)
This item allows you to enable or disable the selected SATA port.
Configuration options: [Disabled] [Enabled]
Hot Plug
These items appears only when the SATA Mode Selection is set to [
AHCI
] and allows
you to enable or disable SATA Hot Plug Support.
Configuration options: [Disabled] [Enabled]
3.6.6
PCH-FW Configuration
This item allows you to configure the firmware TPM.