Home » Asus Manuals » Servers » Asus RS724QA-E6 RS12 » Manual Viewer

Asus RS724QA-E6 RS12 User Guide - Page 62

A.3.9 SETONLINE Command, cfggen, setoffline

View all Asus RS724QA-E6 RS12 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

the disk is still associated with the volume and therefore cannot be addressed by normal I/O requests. If a new disk replaces an offline disk, the new disk is automatically brought online. Otherwise, the disk remains offline until explicitly brought online by SETONLINE command. Command Line - cfggen setoffline Parameters - • - Number of the SAS controller targeted by this command. • - SCSI target ID of the drive targeted by this command. Program Return Value - 0x00 SUCCESS: command completed successfully. 0x01 FAILURE: command failed. A.3.9 SETONLINE Command Note: The SETONLINE command is supported by the DOS, Linux, and WinPE versions of CFGGEN only. The SETONLINE command brings a physical disk in a volume online. This is required only after the physical disk has been taken offline by the SETOFFLINE command. When a physical disk is brought online, the IOC synchronizes the volume. Command Line - cfggen setonline Parameters - • - Number of the controller targeted by this command. • - SCSI target ID of the drive targeted by this command. A-14 Using the CFGGEN IR Configuration Utility Version 1.1 Copyright © 2006, 2007 by LSI Logic Corporation. All rights reserved.

Section	Page
Integrated RAID for SAS	1
Chapter1 Introduction to Integrated RAID	13
1.1 Introduction	13
1.2 Integrated RAID Benefits and Features	14
1.3 Using this Manual	15
Chapter2 Overview of Integrated Mirroring and Integrated Mirroring Enhanced	17
2.1 Introduction	17
2.2 IM and IME Features	18
2.3 IM/IME Description	19
2.4 Integrated RAID Firmware	21
2.4.1 Resynchronization with Concurrent Host I/O Operation	21
2.4.2 Metadata Support	21
2.4.3 Hot Swapping	22
2.4.4 SMART Support	22
2.4.5 Hot Spare Disk	22
2.4.6 Media Verification	23
2.4.7 Disk Write Caching	23
2.4.8 NVSRAM Usage	23
2.5 Fusion-MPT Support	23
Chapter3 Creating IM and IME Volumes	25
3.1 IM/IME Configuration Overview	25
3.2 Creating IM and IME Volumes	26
3.2.1 Creating an IM Volume	27
3.2.2 Creating an IME Volume	29
3.3 Creating a Second IM or IME Volume	29
3.4 Managing Hot Spares	30
3.5 Other Configuration Tasks	32
3.5.1 Viewing Volume Properties	32
3.5.2 Synchronizing an Array	32
3.5.3 Activating an Array	33
3.5.4 Deleting an Array	33
3.5.5 Locating a Disk Drive, or Multiple Disk Drives in a Volume	34
3.5.6 Selecting a Boot Disk	34
Chapter4 Overview of IntegratedStriping	37
4.1 Introduction	37
4.2 IS Features	38
4.3 IS Description	38
4.4 Integrated Striping Firmware	40
4.4.1 Metadata Support	40
4.4.2 SMART Support	40
4.4.3 Disk Write Caching	40
4.5 Fusion-MPT Support	40
Chapter5 Creating Integrated Striping Volumes	41
5.1 IS Configuration Overview	41
5.2 Creating IS Volumes	42
5.3 Creating a Second IS Volume	44
5.4 Other Configuration Tasks	45
5.4.1 Viewing IS Volume Properties	45
5.4.2 Activating an Array	45
5.4.3 Deleting an Array	46
5.4.4 Locating a Disk Drive, or Multiple Disk Drives in a Volume	46
5.4.5 Selecting a Boot Disk	47
AppendixA Using the CFGGEN IR Configuration Utility	49
A.1 Hardware and Software Requirements	50
A.2 CFGGEN Interface Description	51
A.3 CFGGEN Commands	51
A.3.1 Common Command Line Parameters	52
A.3.2 CREATE Command	53
A.3.3 DEFAULTS Command	54
A.3.4 DISPLAY Command	55
A.3.5 FORMAT Command	58
A.3.6 HOTSPARE Command	59
A.3.7 STATUS Command	60
A.3.8 SETOFFLINE Command	61
A.3.9 SETONLINE Command	62
A.3.10 AUTO Command (EFI Version Only)	63
A.3.11 DISABLEIR Command (EFI Version Only)	64
A.3.12 ENABLEIR Command (EFI Version Only)	65
A.3.13 LIST Command (EFI Version Only)	66