Behringer ULTRAGRAPH PRO FBQ3102 Manual - Page 11

Installation

Get Behringer ULTRAGRAPH PRO FBQ3102 PDF manuals and user guides View all Behringer ULTRAGRAPH PRO FBQ3102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

11 ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 4. Installation 4.1 Rack mounting The FBQ1502 requires one height unit (1 HU) for mounting in a 19" rack, the FBQ3102 two height units, and the FBQ6200 three height units. Please allow at least an additional 4" of space for the connectors on the back panel. Be sure that there is enough space around the unit for cooling and please do not place your ULTRAGRAPH PRO on high-temperature devices such as power amplifiers etc. to avoid overheating. For rack mounting, please use M6 metal nuts and bolts. 4.2 Audio connections You will need many different cables for the various applications. The following illustrations show how these cables should be laid out. Please use exclusively high-grade cabels. The ULTRAGRAPH PRO is installed with electronically servo-balanced inputs and outputs to avoid hum noise problems. You can, of course, also connect unbalanced devices to the balanced inputs/ outputs. Either use mono plugs, or connect the ring and sleeve of stereo plugs (bridge pin 1 and pin 3 when using XLR connectors). ◊ Please ensure that only qualified personnel install and operate the ULTRAGRAPH PRO. During installation and operation the user must have sufficient electrical contact to earth. Electrostatic charges might affect the operation of the unit. Balanced use with XLR connectors 21 3 input 1 = ground/shield 2 = hot (+ve) 3 = cold (-ve) 12 3 output For unbalanced use, pin 1 and pin 3 have to be bridged Fig. 4.1: XLR connectors Unbalanced ¼" TS connector strain relief clamp sleeve tip sleeve (ground/shield) tip (signal) Fig. 4.2: ¼" TS connector Balanced ¼" TRS connector strain relief clamp sleeve ring tip sleeve ground/shield ring cold (-ve) tip hot (+ve) For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug. Fig. 4.3: ¼" TRS connector Insert send return ¼" TRS connector strain relief clamp sleeve ring tip sleeve ground/shield ring return (in) tip send (out) Connect the insert send with the input and the insert return with the output of the e ects device. Fig. 4.4: ¼" TRS connector for insert send/return applications

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
11
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual
4.
Installation
4.1
Rack mounting
The FBQ1502 requires one height unit (1 HU) for mounting in a 19" rack,
the FBQ3102 two height units, and the FBQ6200 three height units. Please allow
at least an additional 4" of space for the connectors on the back panel.
Be sure that there is enough space around the unit for cooling and please do
not place your ULTRAGRAPH PRO on high-temperature devices such as power
amplifiers etc. to avoid overheating.
For rack mounting, please use M6 metal nuts and bolts.
4.2
Audio connections
You will need many different cables for the various applications. The following
illustrations show how these cables should be laid out. Please use exclusively
high-grade cabels.
The ULTRAGRAPH PRO is installed with electronically servo-balanced inputs and
outputs to avoid hum noise problems.
You can, of course, also connect unbalanced devices to the balanced inputs/
outputs. Either use mono plugs, or connect the ring and sleeve of stereo plugs
(bridge pin 1 and pin 3 when using XLR connectors).
◊
Please ensure that only qualified personnel install and operate the
ULTRAGRAPH PRO. During installation and operation the user must
have sufficient electrical contact to earth. Electrostatic charges might
affect the operation of the unit.
output
For unbalanced use, pin 1 and pin 3
have to be bridged
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
input
1
2
3
1
2
3
Balanced use with XLR connectors
Fig. 4.1: XLR connectors
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
Unbalanced ¼" TS connector
tip
(signal)
Fig. 4.2: ¼" TS connector
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced ¼" TRS connector
ring
cold (-ve)
tip
hot (+ve)
Fig. 4.3: ¼" TRS connector
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
Connect the insert send with the input and the
insert return with the output of the effects device.
Insert send return ¼" TRS connector
ring
return (in)
tip
send (out)
Fig. 4.4: ¼" TRS connector for insert send/return applications