BenQ BenQ MP776 DLP 3D Projector User Manual - Page 55

Timing of replacing the lamp, Status, Message

Get BenQ BenQ MP776 DLP 3D Projector PDF manuals and user guides View all BenQ BenQ MP776 DLP 3D Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.benq.com for a replacement lamp. The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 59 for details. The following Lamp warning displays will remind you to change the lamp. The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp. Status The lamp has been in operation equivalent to 2500 hours. Install a new lamp for optimal performance. If the projector is normally run with "Economic Mode" selected (See "Lamp Mode (Normal)" on page 50), you may continue to operate the projector until the 2950 hour lamp warning appears. Message Notice Order Replacement Lamp Lamp > 2500 Hours Order a new lamp at lamp.benq.com OK The lamp has been in operation equivalent to 2950 hours. A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time. Notice Replace Lamp Soon Lamp > 2950 Hours Order a new lamp at lamp.benq.com OK The lamp has been in operation equivalent to 3000 hours. It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. If the lamp is not replaced beforehand, it must be replaced after 3000 hours usage. The lamp MUST be replaced before the projector will operate normally. Notice Replace Lamp Now Lamp > 3000 Hours Lamp usage time exceeded Order a new lamp at lamp.benq.com OK Notice Out of Lamp Usage Time Replace lamp (refer to User manual) Then reset lamp timer Order a new lamp at lamp.benq.com OK Maintenance 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Maintenance
55
Timing of replacing the lamp
Timing of replacing the lamp
Timing of replacing the lamp
Timing of replacing the lamp
When the Lamp indicator
Lamp indicator
Lamp indicator
Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Go to
for a replacement lamp.
The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See
"Indicators" on
page 59
for details.
The following Lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
Status
Message
The lamp has been in operation equivalent to 2500
hours. Install a new lamp for optimal
performance. If the projector is normally run with
"Economic Mode" selected (See
"Lamp Mode
(Normal)" on page 50
), you may continue to
operate the projector until the 2950 hour lamp
warning appears.
The lamp has been in operation equivalent to 2950
hours. A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
The lamp has been in operation equivalent to 3000
hours.
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced after
3000 hours usage.
The lamp MUST be replaced before the projector
will operate normally.
OK
Order Replacement Lamp
Lamp > 2500 Hours
Order a new lamp at lamp.benq.com
Notice
OK
Replace Lamp Soon
Lamp > 2950 Hours
Order a new lamp at lamp.benq.com
Notice
OK
Replace Lamp Now
Lamp > 3000 Hours
Lamp usage time exceeded
Order a new lamp at lamp.benq.com
Notice
OK
Out of Lamp Usage Time
Replace lamp (refer to User manual)
Then reset lamp timer
Order a new lamp at lamp.benq.com
Notice