BenQ MP782ST User Manual - Page 24

Operation, Starting up the projector

Get BenQ MP782ST PDF manuals and user guides View all BenQ MP782ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire. 2. Open the lens cover. If it is closed, it could become deformed due to the heat produced by the projection lamp. 3. Press Power on the projector or remote control to start the projector. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Rotate the focus ring to adjust the image clearness. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. 4. If the projector is activated for the first time, select your OSD language following the onscreen instructions. 5. If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 27 for details. 6. Switch all of the connected equipment on. 7. The projector will start to search for input signals. The current input signal being scanned displays in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message "No Signal" will continue displaying until an input signal is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 30 for details. 24 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Operation
24
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
power outlet. Turn on the power outlet switch
(where fitted). Check that the
POWER indicator
light
on the projector lights orange after power has
been applied.
Please use the original accessories (e.g. power cord) only
with the device to avoid possible dangers such as electric
shock and fire.
2.
Open the lens cover. If it is closed, it could become
deformed due to the heat produced by the
projection lamp.
3.
Press
Power
on the projector or remote
control to start the projector. The
POWER
indicator light
flashes green and stays green
when the projector is on.
The start up procedure takes about 30 seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
4.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
5.
If you are prompted for a password, press the
arrow keys to enter a six-digit password. See
"Utilizing the password function" on page 27
for details.
6.
Switch all of the connected equipment on.
7.
The projector will start to search for input
signals. The current input signal being scanned
displays in the upper left corner of the screen.
If the projector doesn't detect a valid signal, the message “No Signal” will continue
displaying until an input signal is found.
You can also press
SOURCE
on the projector or remote control to select your desired
input signal. See
"Switching input signal" on page 30
for details.
If the projector is still hot from
previous activity, it will run
the cooling fan for
approximately 90 seconds
before energizing the lamp.