BenQ MP782ST User Manual - Page 25

Adjusting the projected image, Auto-adjusting the image, Fine-tuning the image clarity - case

Get BenQ MP782ST PDF manuals and user guides View all BenQ MP782ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message "Out of Range" displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 64 for details. Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine-tune the horizontal angle. To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction. If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 29 for details. 2 1 Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes. Be careful when you press the quick-release button as it is close to the exhaust vent where hot air comes from. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. The current source information will be displayed in the corner of the screen for 3 seconds. • The screen will be blank while AUTO is functioning. • This function is only available when a PC signal (analog RGB) is selected. Fine-tuning the image clarity If needed, sharpen the image by rotating the focus ring. Operation 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Operation
25
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message “Out of Range” displayed on a blank screen. Please change to an input
signal which is compatible with the projector's resolution or set the input signal to a lower
setting. See
"Timing chart" on page 64
for details.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the front
of the projector. Once the image is positioned
where you want it, release the quick-release
button to lock the foot in position.
2.
Screw the rear adjuster foot to fine-tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower
the projector. Screw the rear adjuster foot in a reverse
direction.
If the projector is not placed on a flat surface or the
screen and the projector are not perpendicular to each
other, the projected image becomes trapezoidal. To
correct this situation, see
"Correcting keystone" on
page 29
for details.
Auto-adjusting the image
In some cases, you may need to optimize the picture
quality. To do this, press
AUTO
on the projector or
remote control. Within 3 seconds, the built-in
Intelligent Auto Adjustment function will re-adjust the
values of Frequency and Clock to provide the best
picture quality.
The current source information will be displayed in the
corner of the screen for 3 seconds.
•
The screen will be blank while AUTO is functioning.
•
This function is only available when a PC signal (analog RGB) is selected.
Fine-tuning the image clarity
If needed, sharpen the image by rotating the focus ring.
1
2
Do not look into the lens while
the lamp is on. The strong light
from the lamp may cause
damage to your eyes.
Be careful when you press the
quick-release button as it is
close to the exhaust vent where
hot air comes from.