BenQ MP782ST User Manual - Page 42

Controlling the projector remotely through a web browser, If you are in a non-DHCP environment

Get BenQ MP782ST PDF manuals and user guides View all BenQ MP782ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

If you are in a non-DHCP environment: 1. Repeat steps 1-4 above. 2. Press to highlight DHCP and press / to select Off. 3. Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings. 4. Press to select the item you want to modify and press MODE/ENTER. 5. Press / to move the cursor and the press / to enter the value. 6. To save the settings, press MODE/ENTER. If you do not want to save the settings, press MENU/EXIT. 7. Press to highlight Apply and press MODE/ENTER. Controlling the projector remotely through a web browser Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector. 1. Enter the address of the projector in the address bar of your browser and click GO. 2. The remote network operation page opens. This page allows you to operate the projector as if you were using the remote control or control panel on the projector. i ii i i i. These buttons function the same as the ones on the OSD menus or remote control. See "2. PICTURE menu" on page 49 and "Remote control" on page 11 for details. The Menu button can also be used to go back to previous OSD menu, exit and save menu settings. ii. To switch input signal, click on your desired signal. The source list varies according to the connectors available on the projector. "DVI-D 1" stands for the DVI-D signal; "Video 1" stands for the Video signal; "S-Video 1" stands for the S-Video signal. 42 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Operation
42
If you are in a non-DHCP environment:
1.
Repeat steps 1-4 above.
2.
Press
to highlight
DHCP
and press
/
to select
Off
.
3.
Contact your ITS administrator for information on the
Projector IP Address
,
Subnet
Mask
,
Default Gateway
, and
DNS Server
settings.
4.
Press
to select the item you want to modify and press
MODE/ENTER
.
5.
Press
/
to move the cursor and the press
/
to enter the value.
6.
To save the settings, press
MODE/ENTER
. If you do not want to save the settings,
press
MENU/EXIT
.
7.
Press
to highlight
Apply
and press
MODE/ENTER
.
Controlling the projector remotely through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
1.
Enter the address of the projector in the address bar of your browser and click
GO
.
2.
The remote network operation page opens. This page allows you to operate the
projector as if you were using the remote control or control panel on the projector.
i.
These buttons function the same as the ones on the OSD menus or remote
control. See
"2. PICTURE menu" on page 49
and
"Remote control" on page 11
for
details.
The Menu button can also be used to go back to previous OSD menu, exit and save menu
settings.
ii.
To switch input signal, click on your desired signal.
The source list varies according to the connectors available on the projector. “DVI-D 1” stands
for the DVI-D signal; “Video 1” stands for the Video signal; “S-Video 1” stands for the S-Video
signal.
i
i
i
ii