BenQ MS513 DLP Projector MS513, MX514, MW516 User Manual - Page 45

Personalizing the projector menu display, Select the lamp saver mode

Get BenQ MS513 DLP Projector PDF manuals and user guides View all BenQ MS513 DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. • Reminder Message in the SYSTEM SETUP: Advanced > Menu Settings menu sets whether to display reminder messages on screen. Use / to select your desired setting. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Select the lamp saver mode • Using the remote control. Press Smart Eco and Highlight Lamp mode and press / to select Normal/ Economic/Smart Eco. • Using the OSD menu. 1. Press Menu/Exit and then press / until the SYSTEM SETUP: Advanced menu is highlighted. 2. Press to highlight Lamp mode and press Mode/Enter. The Lamp Settings page displays. 3. Highlight Lamp mode and press / to select Normal/Economic/Smart Eco. The lamp brightness vary from the different lamp mode,see the description list in table below. Lamp mode Description Normal 100% lamp brightness. Economic Smart Eco 80% lamp power consumption. This is default setting. Lamp power consumption will save from 30% to 100% dynamically by detecting the content brightness level. If the Economic mode is selected, the light output will be reduced and result in darker projected pictures. Operation 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Operation
45
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time
in the
SYSTEM SETUP: Advanced
>
Menu Settings
menu
sets the length of time the OSD will remain active after your last key press. The time
length ranges from 5 to 30 seconds in 5-second increments. Use
/
to select a
suitable time frame.
•
Menu position
in the
SYSTEM SETUP: Advanced
>
Menu Settings
menu sets
the OSD position in five locations. Use
/
to select a preferred position.
•
Language
in the
SYSTEM SETUP: Basic
menu sets your familiar language for the
OSD menus. Use
/
to select your language.
•
Reminder Message
in the
SYSTEM SETUP: Advanced
>
Menu Settings
menu
sets whether to display reminder messages on screen. Use
/
to select your
desired setting.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen
to be displayed during projector start-up. Use
/
to select a screen.
Select the lamp saver mode
•
Using the remote control.
Press
Smart Eco
and Highlight
Lamp mode
and press
/
to select
Normal/
Economic/Smart Eco
.
•
Using the OSD menu.
1.
Press
Menu/Exit
and then press
/
until the
SYSTEM SETUP: Advanced
menu is highlighted.
2.
Press
to highlight
Lamp mode
and press
Mode/Enter
. The Lamp Settings page
displays.
3.
Highlight
Lamp mode
and press
/
to select
Normal/Economic/Smart
Eco
.
The lamp brightness vary from the different lamp mode,see the description list
in table below.
If the Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Lamp mode
Description
Normal
100% lamp brightness
.
Economic
80% lamp power consumption.
Smart Eco
This is default setting. Lamp power consumption will save from 30% to
100% dynamically by detecting the content brightness level.