Bosch SHE3AEM2N Installation Instructions - Page 12

Dishwasher Connection

Get Bosch SHE3AEM2N PDF manuals and user guides View all Bosch SHE3AEM2N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

en-us Dishwasher Connection 2. If using the Top Mount, and screw the 1/2" (12.7mm) wood screws through the holes in the mounting brackets. Choose the bracket hole best suited for your installation. If the dishwasher came with a protective barrier, screw through the barrier. 3. For Side Mount, lift the flap on the deco strip and insert the 1/2" (12.7mm) wood screws underneath. effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 - 145 psi (1 - 10 bar). WARNING Scalding Hazard ▶ Do not perform any work on a pressured hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off. NOTICE: Soldering plumbing lines ▶ Temperatures required for soldering and sweating will damage the dishwasher. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher. Plumbing codes ▶ Check local plumbing codes for approved plumbing procedures and accessories. All plumbing should be done in accordance with national and local codes. Note Important notes for water connection: ¡ If using a solder joint instead of a compression fitting, be sure to complete all solder connections before connecting the water supply line to the dishwasher. ¡ Use an approved dishwasher water supply line with the correct fittings for this connection. ¡ If using copper tubing or other material not depicted in this manual for water supply, defer to a licensed plumber for proper installation. ¡ Always use appropriate seals when making plumbing connections. 1. Flush the incoming water line for approximately 1 minute to clear any foreign material. 2. Connect the dishwasher water supply line to the water shut off valve. ‒ Install a shut off valve if one isn't already in the supply line. ‒ Make sure there are no sharp bends or kinks in the water line that might restrict water flow. Dishwasher Connection 5 Dishwasher Connection Dishwasher Connection Follow these instructions to connect the dishwasher. 5.1 Installing the Water Inlet Connection The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose 12 3. Properly tighten all water connections.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
en-us
Dishwasher Connection
12
2.
If using the Top Mount, and screw the 1/2" (12.7mm)
wood screws through the holes in the mounting
brackets. Choose the bracket hole best suited for your
installation.
If the dishwasher came with a protective barrier, screw
through the barrier.
3.
For Side Mount, lift the flap on the deco strip and insert
the 1/2" (12.7mm) wood screws underneath.
5
Dishwasher Connection
Follow these instructions to connect the dishwasher.
5.1
Installing the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120° F (49° C) water to the dishwasher.
Water that is too hot can cause some detergents to lose
effectiveness. Lower water temperatures will increase run
times. The hot water supply pressure must be between 15
- 145 psi (1 - 10 bar).
WARNING
Scalding Hazard
▶
Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
NOTICE:
Soldering plumbing lines
▶
Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
▶
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
Note
Important notes for water connection:
¡
If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡
Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡
If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
¡
Always use appropriate seals when making plumbing
connections.
1.
Flush the incoming water line for approximately 1
minute to clear any foreign material.
2.
Connect the dishwasher water supply line to the water
shut off valve.
‒
Install a shut off valve if one isn’t already in the
supply line.
‒
Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
3.
Properly tighten all water connections.