Bosch SHE3AEM2N Installation Instructions - Page 7

Installation Preparation, Installation Procedure

Get Bosch SHE3AEM2N PDF manuals and user guides View all Bosch SHE3AEM2N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Installation Preparation 3 Installation Preparation Installation Preparation After locating the proper place for your dishwasher, create an opening to allow for water, drain and electrical lines on the appropriate side. 1. Cut a hole within the 7 x 2.5" area shown. Installation Preparation en-us 1. Carefully flip the unit over onto its back side with the door facing up. 2 ½" (6.3 cm) 7" (17.8 cm) ø 2 ½" (6.3 cm) or 2. Remove the toe panel from the front of the unit (set aside for later) and loosen the feet slightly. If the opening is made through wood, sand it smooth. If the opening is made through metal, use the Edge Protector with Power Cord clips Kit SMZEPCC1UC. 2. Remove the drain hose from inside the dishwasher. 3. Remove the toe panel fleece from the back of the dishwasher. 3. Attach the elbow to the water inlet valve on the front of the dishwasher. Installation Procedure 4 Installation Procedure Installation Procedure Follow these instructions to install the dishwasher. 4.1 Attach Water Inlet Hose NOTICE: Avoid cross-threading ▶ Cross-threading will cause leaks. Teflon tape ▶ Do not use Teflon tape; it could cause leaks and damage floors or cabinetry. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Installation Preparation
en-us
7
3
Installation Preparation
After locating the proper place for your dishwasher, create
an opening to allow for water, drain and electrical lines on
the appropriate side.
1.
Cut a hole within the 7 x 2.5" area shown.
7"
(17.8 cm)
2 ½"
(6.3 cm)
ø 2 ½"
(6.3 cm)
or
If the opening is made through wood, sand it smooth.
If the opening is made through metal, use the Edge
Protector with Power Cord clips Kit SMZEPCC1UC.
2.
Remove the drain hose from inside the dishwasher.
3.
Remove the toe panel fleece from the back of the
dishwasher.
4
Installation Procedure
Follow these instructions to install the dishwasher.
4.1
Attach Water Inlet Hose
NOTICE:
Avoid cross-threading
▶
Cross-threading will cause leaks.
Teflon tape
▶
Do not use Teflon tape; it could cause leaks and
damage floors or cabinetry.
1.
Carefully flip the unit over onto its back side with the
door facing up.
2.
Remove the toe panel from the front of the unit (set
aside for later) and
loosen the feet slightly.
3.
Attach the elbow to the water inlet valve on the front of
the dishwasher.