Bosch SHX78B75UC Use and Care Manuals - Page 47

Cleaning filters, Filter system, Sensors,

Page 47 highlights

Troubleshooting en-us Issue Appliance interior still wet after wash cycle. Food remnants on dishware. Cause and troubleshooting Not an error. Condensation drying creates water droplets in the tub. This is normal. Moisture in the air condenses on the inside walls of the appliance, runs off, and is pumped out. No action required. Dishware was placed too close together or rack is overfilled. 1. Arrange dishware with sufficient space in be- tween. The spray jets must reach the surfaces of the dishware. 2. Avoid points of contact. Spray arm rotation is blocked. ▶ Arrange dishware so it does not obstruct spray arm rotation. Spray arm nozzles are blocked. ▶ Clean the Spray arms → Page 42. Filters are dirty. ▶ Clean the filters. → "Cleaning filters", Page 41 Filters are inserted incorrectly and/or not engaged. 1. Insert the filters properly. → "Filter system", Page 41 2. Twist filters into place. Selected wash cycle is too light. ▶ Select a more intensive cycle. ▶ Adjust the sensitivity of the sensors. → "Sensors", Page 10 Dishware has been precleaned too intensively. Then the sensors choose a lighter cycle. Stubborn remnants cannot be entirely removed. ▶ Only remove large remnants of food and do not pre-rinse dishware. ▶ Adjust the sensitivity of the sensors. → "Sensors", Page 10 Tall narrow containers in corner areas are not rinsed out adequately. ▶ Do not position tall narrow containers at too great an angle or in corner areas. Upper rack on right and left not set to same height. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

Troubleshooting
en-us
47
Issue
Cause and troubleshooting
Appliance interior
still wet after wash
cycle.
Not an error. Condensation drying creates water
droplets in the tub. This is normal. Moisture in the
air condenses on the inside walls of the appli-
ance, runs off, and is pumped out.
No action required.
Food remnants on
dishware.
Dishware was placed too close together or rack is
overfilled.
1.
Arrange dishware with sufficient space in be-
tween.
The spray jets must reach the surfaces of the
dishware.
2.
Avoid points of contact.
Spray arm rotation is blocked.
Arrange dishware so it does not obstruct spray
arm rotation.
Spray arm nozzles are blocked.
Clean the Spray arms
Page 42
.
Filters are dirty.
Clean the filters.
"Cleaning filters", Page 41
Filters are inserted incorrectly and/or not en-
gaged.
1.
Insert the filters properly.
"Filter system", Page 41
2.
Twist filters into place.
Selected wash cycle is too light.
Select a more intensive cycle.
Adjust the sensitivity of the sensors.
"Sensors", Page 10
Dishware has been precleaned too intensively.
Then the sensors choose a lighter cycle. Stub-
born remnants cannot be entirely removed.
Only remove large remnants of food and do not
pre-rinse dishware.
Adjust the sensitivity of the sensors.
"Sensors", Page 10
Tall narrow containers in corner areas are not
rinsed out adequately.
Do not position tall narrow containers at too
great an angle or in corner areas.
Upper rack on right and left not set to same
height.