Bosch SHX78B75UC Use and Care Manuals - Page 53

Issue, Cause and troubleshooting, Reset

Page 53 highlights

Troubleshooting en-us Issue All LEDs light up or flash. Cause and troubleshooting Electronics have detected a fault. 1. Press the main switch button for approx. 4 sec- onds. → "Controls", Page 13 The appliance is reset and restarted. 2. If the problem occurs again: ‒ Switch off the appliance. ‒ Unplug the power plug or switch off the cir- cuit breaker in the fuse box. ‒ Wait at least 2 minutes. ‒ Switch on the circuit breaker in the fuse box or plug in the power plug. ‒ Switch on the appliance. 3. If the problem occurs again: ‒ Contact customer service. → "Customer Service", Page 57 UP appears on the display. A software update is available. ▶ Press the remote start button to install the soft- ware update. a After a successful software update, "Suc" appears on the display for a few seconds. Water is left in the Filter system or area under the filters is blocked. appliance at the end 1. Clean the Filters → Page 41. of the program. 2. Clean the Drain pump → Page 55. Program has not yet ended. ▶ Wait until the program ends or terminate the program with Reset. ▶ → "Terminating the wash cycle", Page 33 Appliance cannot be Software update is taking place. switched on or oper- ▶ Wait until the software update has finished. ated. Appliance functions have failed. 1. Pull out the power cord plug or switch off the breaker. 2. Wait at least 2 minutes. 3. Connect the appliance to the power supply. 4. Switch the appliance on. Appliance does not The breaker has tripped. start. ▶ Check the relevant breaker. Power cord is not inserted. 1. Check whether the power outlet is working. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

Troubleshooting
en-us
53
Issue
Cause and troubleshooting
All LEDs light up or
flash.
Electronics have detected a fault.
1.
Press the main switch button for approx. 4 sec-
onds.
"Controls", Page 13
The appliance is reset and restarted.
2.
If the problem occurs again:
Switch off the appliance.
Unplug the power plug or switch off the cir-
cuit breaker in the fuse box.
Wait at least 2 minutes.
Switch on the circuit breaker in the fuse box
or plug in the power plug.
Switch on the appliance.
3.
If the problem occurs again:
Contact customer service.
"Customer Service", Page 57
UP appears on the
display.
A software update is available.
Press the remote start button to install the soft-
ware update.
a
After a successful software update, "Suc" ap-
pears on the display for a few seconds.
Water is left in the
appliance at the end
of the program.
Filter system or area under the filters is blocked.
1.
Clean the Filters
Page 41
.
2.
Clean the Drain pump
Page 55
.
Program has not yet ended.
Wait until the program ends or terminate the
program with
Reset
.
"Terminating the wash cycle", Page 33
Appliance cannot be
switched on or oper-
ated.
Software update is taking place.
Wait until the software update has finished.
Appliance functions have failed.
1.
Pull out the power cord plug or switch off the
breaker.
2.
Wait at least 2 minutes.
3.
Connect the appliance to the power supply.
4.
Switch the appliance on.
Appliance does not
start.
The breaker has tripped.
Check the relevant breaker.
Power cord is not inserted.
1.
Check whether the power outlet is working.