Bosch SHX7ER55UC Instructions for Use - Page 15

Operating the Dishwasher - 01

Page 15 highlights

Operating the Dishwasher Start the dishwasher 1 Open the door and press the [On/Off] button. The LED of the last selected cycle flashes. 2 Select a cycle and desired options. 3 Press [Start] and close the door to begin the cycle. Cancel a cycle 1 Open the door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press and hold the [Start] button for approximately 3 seconds until the display reads "0:01". 3 Close the door and wait about 1 minute while the dishwasher drains. 4 Open the door and press the [On/Off] button. Interrupt a cycle 1 Open the door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press the [On/Off] button to turn the unit off. 3 To resume the cycle, press the On/Off button and close the dishwasher door. Setting the amount of rinse aid The amount of rinse aid dispensed can be set from "r:00" to "r:06". To change the setting: 1 Open the door and press the [On/Off] button. 2 Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00". 3 Release both buttons. 4 Press the "A" button until the display shows "r:05". 5 Press the "C" button to select the desired setting. "r:00" = dispenser is OFF "r:01" = lowest setting "r:02" = low setting "r:03" = medium setting "r:04" = medium/high setting "r:05" = high setting "r:06" = highest setting 6 Press [Start] to save the setting and close the door. InfoLight An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the LED is not visible. To change the setting: 1 Open the door and press the [On/Off] button. 2 Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00". 3 Release both buttons. 4 Press the "A" button until the display shows "1:01". 5 Press the "C" button to switch between "1:01" = ON and "1:00" = OFF and press [Start] to save. Delay Start You can delay the start of the cycle in one hour increments up to 24 hours. To set delay start: 1 Open the door and press the [On/Off] button. 2 Press the [+] button until the display jumps to "h:01". 3 Press the [+] or [-] button until the displayed time corresponds with your requirements. h:01 = 1 hour delay h:24 = 24 hour delay 4 Press [Start] to activate delay start. To cancel delay start: 1 Press the [+] or [-] button until "h:00" is indicated on the digital display. 2 Press [Start] to save setting and close the door. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

13
Operating the Dishwasher
Start the dishwasher
1
Open the door and press the
[On/Off]
button. The LED of the last selected cycle flashes.
2
Select a cycle and desired options.
3
Press
[Start]
and close the door to begin the cycle.
Cancel a cycle
1
Open the door just far enough to expose the control panel. Be careful of hot water that may splash out.
2
Press and hold the
[Start]
button for approximately 3 seconds until the display reads
“0:01”.
3
Close the door and wait about 1 minute while the dishwasher drains.
4
Open the door and press the
[On/Off]
button.
Interrupt a cycle
1
Open the door just far enough to expose the control panel. Be careful of hot water that may splash out.
2
Press the
[On/Off]
button to turn the unit off.
3
To resume the cycle, press the
On/Off
button and close the dishwasher door.
Setting the amount of rinse aid
The amount of rinse aid dispensed can be set from “r:00” to “r:06”.
To change the setting:
1
Open the door and press the
[On/Off]
button.
2
Hold down the “
A
” button (see page 4) and press
[Start]
until the display indicates “
H:00
”.
3
Release both buttons.
4
Press the “
A
” button until the display shows “
r:05
”.
5
Press the “
C
” button to select the desired setting.
r:00
” = dispenser is OFF
r:01
” = lowest setting
r:02
” = low setting
r:03
” = medium setting
r:04
” = medium/high setting
r:05
” = high setting
r:06
” = highest setting
6
Press
[Start]
to save the setting and close the door.
InfoLight
An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the LED is not visible.
To change the setting:
1
Open the door and press the
[On/Off]
button.
2
Hold down the “
A
” button (see page 4) and press
[Start]
until the display indicates “
H:00
”.
3
Release both buttons.
4
Press the “
A
” button until the display shows “
1:01
”.
5
Press the “
C
” button to switch between “
1:01
” = ON and “
1:00
” = OFF and press
[Start]
to save.
Delay Start
You can delay the start of the cycle in one hour increments up to 24 hours.
To set delay start:
1
Open the door and press the
[On/Off]
button.
2
Press the
[+]
button until the display jumps to “
h:01
”.
3
Press the
[+]
or
[-]
button until the displayed time corresponds with your requirements.
h:01
= 1 hour delay
h:24
= 24 hour delay
4
Press
[Start]
to activate delay start.
To cancel delay start:
1
Press the
[+]
or
[-]
button until “h:00” is indicated on the digital display.
2
Press
[Start]
to save setting and close the door.