Home » Bosch Manuals » Dishwashers » Bosch SHXM63W55N » Manual Viewer

Bosch SHXM63W55N Instructions for Use - Page 27

Delay Start, Wash cycle end, Auto power off

Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Delay Start You can delay the start of the cycle in one hour increments up to 24 hours. œ:‹, 1 hour delay œ:ƒ... 24 hours delay To set Delay start: 1. Open the door and press the On/Off button (. Select a cycle. 2. Press the Delay button from the wash cycle options H until the displayed time corresponds with your requirements. 3. Press the Start button P to activate Delay start. To cancel Delay start: 1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display 8. 2. Press the Start button P to save setting. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. Wash cycle end The wash cycle has ended when the display 8 reads ‹:‹‹. If the signal tone has been set, the wash cylce end is also indicated by a buzzer. Off low medium loud Operating the Dishwasher en-us To change the signal volume: 1. Open the door. 2. Press the On/Off button (. 3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons. 4. Press function key # until the display shows ›:‹ƒ. 5. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value the display jumps back to off). 6. Press Start button P to save the setting. Auto power off This setting determines the length of time the control panel stays illuminated after the cycle is complete. To save energy the recommended setting is ˜:‹,. This setting can be adjusted from ˜:‹‹ to ˜:‹ƒ. dishwasher does not turn off automatically dishwasher turns off automatically after 1 minute dishwasher turns off automatically after 120 minutes (2 hours) To change the setting: 1. Press the On/Off button (. 2. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number). 3. Release both buttons. 4. Press the function key # until the display 8 indicates ˜:‹x. 5. Press the function key 3 until the display corresponds with your requirements. 6. Press the Start button P. 27

Section	Page
Table of contents	3
en-us Operating instructions	3
( Safety Definitions 5	3
( IMPORTANT SAFETY INSTRUCTIONS 6	3
ƒ Causes of Damage 9	3
* Getting Started 10	3
, Rinse Aid 12	3
- Loading the Dishwasher 13	3
. Detergent 21	3
/ Dishwasher Cycles 23	3
0 Dishwasher Cycle Options 24	3
1 Operating the Dishwasher 26	3
2 Care and Maintenance 29	3
3 Troubleshooting 33	3
4 Customer Service 37	3
‡ Statement of Limited Product Warranty 38	3
( Safety Definitions	5
Safety Definitions	5
9 WARNING	5
9 CAUTION	5
NOTICE	5
Note:	5
( IMPORTANT SAFETY INSTRUCTIONS	6
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
To reduce the risk of fire, electrical shock, or serious injury, observe the following:	6
Risk of fire, electrical shock, or serious injury	6
9 WARNING	6
Risk of injury or death!	6
9 WARNING	6
Risk of injury!	6
9 WARNING	6
Risk of electrical shock or fire!	6
9 WARNING	6
Health hazard!	6
GROUNDING INSTRUCTIONS	7
9 WARNING	7
Risk of electric shock!	7
Safe Operation	7
9 CAUTION	7
9 WARNING	7
Risk of injury!	7
Child Safety	8
Proper Care and Maintenance	8
9 WARNING	8
Risk of explosion!	8
NOTICE	8
9 WARNING	8
State of California Proposition 65 Warnings!	8
ƒ Causes of Damage	9
Causes of Damage	9
NOTICES	9
* Getting Started	10
Getting Started	10
Appliance overview	10
Operating panel	11
Dishwasher interior components	11
Display indicators	11
Menu overview	11
Setting	11
Factory setting	11
Description	11
, Rinse Aid	12
Rinse Aid	12
Note:	12
Adding rinse aid	12
NOTICE	12
1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pull it open.	12
2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill.	12
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	12
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	12
NOTICE	12
Setting the amount of rinse aid used	12
Setting	12
Amount	12
1. Open the door.	13
2. Press the On/Off button (.	13
3. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	13
4. Press the function key # until the display 8 shows §:‹†.	13
5. Press the function key 3 to select the desired setting.	13
6. Press the Start button P to save the setting.	13
Turning off rinse aid indicator	13
NOTICE	13
- Loading the Dishwasher	13
Loading the Dishwasher	13
Dishware material	13
Note:	13
Recommended	13
Not Recommended	14
Loading the racks	14
For best dishwashing results, observe the following when loading the dishwasher:	14
NOTICE	14
Loading the upper rack	14
Note:	14
Loading the lower rack	14
Recommended loading pattern	15
12 place setting	15
Lower rack 9\	15
Upper rack 12	15
Note:	15
Third rack 1*	15
Additional loading pattern	15
10 place setting	15
Lower rack 9\	15
Upper rack 12	15
Note:	15
Third rack 1*	16
Loading the silverware basket	16
9 WARNING	16
Risk of injury!	16
Long silverware basket	16
Note:	16
Unloading the dishwasher	16
Note:	16
Adjusting the height of the rack	17
With silverware basket	17
Upper rack	17
Lower rack	17
9.4 in (24 cm)	17
13.4 in (34 cm)	17
10.4 in (26.5 cm)	17
12 in (30.5 cm)	17
11.4 in (29 cm)	17
11 in (28 cm)	17
With third rack	17
Upper rack	17
Lower rack	17
7 in (18 cm)	17
13.4 in (34 cm)	17
8 in (20.5 cm)	17
12 in (30.5 cm)	17
9 in (23 cm)	17
11 in (28 cm)	17
RackMatic®	17
1. Pull the upper rack out of the dishwasher until it stops.	17
2. To lower the rack, push the RackMatic® lever inward.	17
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	17
Note:	17
Rack accessories	18
Flip tines	18
Third rack	18
Cup shelves	18
Removing/Installing third rack	19
Removing third rack 1*	19
1. Pull out third rack all the way (1).	19
2. Lift upper rollers over the stopper hooks of both rails (2).	19
3. Pull third rack out forward and upward so the the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	19
Installing third rack 1*	19
1. Pull out third rack rails all the way (1).	19
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	19
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	19
4. Push in third rack (4).	19
Removing/Installing upper rack with Rackmatic®	20
Removing upper rack 12	20
1. Pull out upper rack all the way (1).	20
2. Lift front rollers over the stopper hook of the rail (2).	20
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	20
Installing upper rack 12	20
1. Pull out upper rack rails all the way (1).	20
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	20
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	20
4. Push in upper rack (4).	20
. Detergent	21
Detergent	21
NOTICE	21
Note:	21
Wash Cycle	21
Hard Water/ Heavy Soil	21
Medium Water/ Medium Soil	21
Soft Water/ Little Soil	21
Adding detergent	22
1. If the detergent dispenser 92 is still closed, actuate the locking bar 9: to open it.	22
Note:	22
2. Pour detergent into the dry detergent dispenser 92 only. Add detergent. Do not overfill the detergent dispenser.	22
Note:	22
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed and press down firmly until it clicks.	22
Tip:	22
/ Dishwasher Cycles	23
Dishwasher Cycles	23
Wash cycle	23
Recommended use	23
Possible wash cycle option	23
Note:	23
Note:	23
The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9*. A single dose of detergent was inserted into the detergent dispenser 92, with no detergent...	23
0 Dishwasher Cycle Options	24
Dishwasher Cycle Options	24
Delay	24
Half Load	24
Sanitize	24
Extra Dry	24
Wash Cycle Information	24
Note:	25
Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...	25
1 Operating the Dishwasher	26
Operating the Dishwasher	26
Note:	26
9 WARNING	26
Risk of injury!	26
Protection against unintentional operation	26
This function will be activated when:	26
Note:	26
AquaSensor	26
AquaSensor	26
Switching the appliance on	26
1. Turn the water supply on fully.	26
2. Press the On/Off button (.	26
3. Press Start button P.	26
Note:	26
Time display	26
Delay Start	27
To set Delay start:	27
1. Open the door and press the On/Off button (. Select a cycle.	27
2. Press the Delay button from the wash cycle options H until the displayed time corresponds with your requirements.	27
3. Press the Start button P to activate Delay start.	27
To cancel Delay start:	27
1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display 8.	27
2. Press the Start button P to save setting.	27
Note:	27
Wash cycle end	27
To change the signal volume:	27
1. Open the door.	27
2. Press the On/Off button (.	27
3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	27
4. Press function key # until the display shows ›:‹ƒ.	27
5. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value ›:‹„, the display jumps back to ›:‹‹ (off).	27
6. Press Start button P to save the setting.	27
Auto power off	27
To change the setting:	27
1. Press the On/Off button (.	27
2. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number).	27
3. Release both buttons.	27
4. Press the function key # until the display 8 indicates ˜:‹x.	27
5. Press the function key 3 until the display corresponds with your requirements.	27
6. Press the Start button P.	27
Switching off the appliance	28
Short time after the end of the wash cycle:	28
1. Open the door.	28
2. Switch off On/Off button (.	28
3. Turn off water supply.	28
4. Remove the utensils when they have cooled down.	28
9 WARNING	28
Risk of injury!	28
Interrupting the wash cycle	28
9 CAUTION	28
1. Open the door.	28
2. Switch off On/Off switch (.	28
3. To continue the wash cycle, switch on the On/Off switch ( again.	28
4. Close the door.	28
Note:	28
Terminating the wash cycle (Reset)	28
Terminating the wash cycle	28
1. Press and hold Start button P for approximately 3 seconds until the display reads ‹:‹‚.	28
2. Wait about 1 minute while the dishwasher drains.	28
3. Press On/Off button (.	28
Changing the wash cycle	28
InfoLight®	28
To change the setting:	29
1. Open the door.	29
2. Press the On/Off button (.	29
3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	29
4. Press function key # until the display shows ‚:‹‚.	29
5. Press the function key 3 to switch the InfoLight® feature on ‚:‹‚ or off ‚:‹‹.	29
6. Press Start button P to save the setting.	29
Intensive drying	29
1. Open the door.	29
2. Press the On/Off button (.	29
3. Hold down function key # and press Start button P until the display 8 indicates š:x (x can be any number).	29
4. Release both buttons.	29
5. Press function key # until the display 8 indicates the factory set value š:‹‹.	29
6. Press function key 3 to switch the Extra dry feature on š:‹‚ or off š:‹‹.	29
7. Press Start button P to save setting.	29
2 Care and Maintenance	29
Care and Maintenance	29
Overall condition of the dishwasher	29
NOTICE	29
9 WARNING	30
Filters	30
Filter components	30
The filter system 1b consists of three parts.	30
Cleaning intervals	30
Your filter system may need to be cleaned when:	30
Cleaning interval	30
Use this setting,	30
Note:	30
To check or clean the filter system:	31
1. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	31
2. Remove any residue and clean filters by rinsing under running water. Note: do not use abrasive brushes or steel wool, etc., as they may damage the filter.	31
3. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	31
Spray arms	31
Check spray arms 1:, 1R for grease and limescale deposits. If you find such deposits:	31
Drain pump	32
Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case:	32
Note:	32
Preparing your unit for vacation	32
NOTICE	32
Winterizing your unit	32
NOTICE	32
3 Troubleshooting	33
Troubleshooting	33
Problem	33
Cause	33
Action	33
Note:	33
Note:	34
Note:	34
Note:	34
Note:	35
Note:	35
--------	36
4 Customer Service	37
Customer Service	37
1. Call us at 1-800-944-2904	37
2. Contact Customer Service from our web site: www.bosch-home.com/us or www.bosch-home.ca	37
3. Contact your installer or the Bosch Authorized Service Contractor in your area.	37
4. Write us:	37
‡ Statement of Limited Product Warranty	38
Statement of Limited Product Warranty	38
What this Warranty Covers & Who it Applies to:	38
The limited warranty provided by BSH Home Appliances Corporation (BSH) in this Statement of Limited Product Warranty applies only to Bosch® dishwashers (“Product”) sold to you, the first using purchaser, provided that the Product was purchased:	38
How Long the Warranty Lasts	38
Extended Limited Warranty	38
BSH also provides these additional limited warranties:	38
Repair/Replace as Your Exclusive Remedy	39
Out of Warranty Product	39
Warranty Exclusions	39
The warranty coverage described herein excludes all defects or damage that are not the direct fault of BSH, including without limitation, one or more of the following:	39
How to Obtain Warranty Service	41
Table des matières	42
fr-ca Notice d'utilisation	42
( Indications de sécurité 44	42
( CONSIGNES DE SÉCURITÉ IMPORTANTES 45	42
ƒ Causes de pannes 49	42
* Mise en marche 50	42
, Produit de rinçage 53	42
- Chargement du lave-vaisselle 55	42
. Détergent 63	42
/ Cycles du lave-vaisselle 65	42
0 Options de cycles du lave-vaisselle 66	42
1 Mise en marche du lave-vaisselle 68	42
2 Entretien et maintenance 73	42
3 Dépannage 77	42
4 Service à la clientèle 81	42
‡ Déclaration de la garantie limitée du produit 82	42
( Indications de sécurité	44
Indications de sécurité	44
9 AVERTISSEMENT	44
9 ATTENTION	44
AVIS	44
Remarque :	44
( CONSIGNES DE SÉCURITÉ IMPORTANTES	45
CONSIGNES DE SÉCURITÉ IMPORTANTES	45
LISEZ ET CONSERVEZ CES INSTRUCTIONS	45
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :	45
Risque d'incendie, de choc électrique, ou de blessures graves	45
9 AVERTISSEMENT	45
Risque de blessure ou de décès !	45
9 AVERTISSEMENT	45
Risque de blessures !	45
9 AVERTISSEMENT	45
Risque de choc électrique ou d'incendie !	45
9 AVERTISSEMENT	45
Risque pour la santè !	45
INSTRUCTIONS DE MISE À LA TERRE	46
9 AVERTISSEMENT	46
Risque de choc électrique !	46
Fonctionnement normal	46
9 ATTENTION	46
9 AVERTISSEMENT	47
Risque de blessures !	47
Sécurité pour enfants	47
Entretien et maintenance corrects	47
9 AVERTISSEMENT	47
Risque d’explosion !	47
AVIS	48
9 AVERTISSEMENT	48
Mises en garde conformément à la proposition 65 de l'État de Californie !	48
ƒ Causes de pannes	49
Causes de pannes	49
AVIS	49
* Mise en marche	50
Mise en route	50
Vue d'ensemble de l'appareil	50
Panneau de commande	51
Composants internes du lave-vaisselle	51
Indicateurs	51
Réglages	52
Réglage	52
Réglages d'usine	52
Description	52
, Produit de rinçage	53
Produit de rinçage	53
Remarque :	53
Ajout de produit de rinçage	53
AVIS	53
1. Ouvrez le distributeur de liquide de rinçage 9* en appuyant sur le loquet du couvercle et en tirant celui-ci.	53
2. Ajoutez le produit de rinçage liquide au distributeur 9* à pleine capacité. Ne le remplissez pas outre mesure.	53
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	53
4. Essuyez tout excédent de produit de nettoyage déversé lorsque le réservoir est plein.	53
AVIS	53
Réglage de la quantité de produit de rinçage utilisé	54
Réglage	54
Quantité	54
1. Ouvrez la porte.	54
2. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	54
3. Maintenez la touche #enfoncée et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur 8 indique š:‹x (x peut être un nombre quelconque). Relâchez les deux boutons.	54
4. Appuyez sur la touche de fonction # jusqu'à ce que l'afficheur 8 indique §:‹†.	54
5. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	54
6. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le paramètre.	54
Désactivation de l'indicateur de produit de rinçage	54
AVIS	54
- Chargement du lave-vaisselle	55
Chargement du lave-vaisselle	55
Matériaux lavables au lave-vaisselle	55
Remarque :	55
Recommandé	55
Non recommandé	55
Chargement des paniers	56
Pour obtenir les meilleurs résultats, respectez les instructions suivantes lors du chargement de la vaisselle :	56
AVIS	56
Chargement du panier supérieur	56
Remarque :	56
Chargement du panier inférieur	56
Mode de chargement recommandé	56
Réglage 12 places	56
Panier inférieur 9\	56
Panier supérieur 12	57
Remarque :	57
Troisième panier 1*	57
Configuration de chargement supplémentaire	57
Réglage 10 places	57
Panier inférieur 9\	57
Panier supérieur 12	57
Remarque :	57
Troisième panier 1*	58
Chargement du panier à ustensiles	58
9 AVERTISSEMENT	58
Risque de blessures !	58
Paniers à ustensiles longs	58
Remarque :	58
Retrait de la vaisselle	59
Remarque :	59
Réglage de la hauteur du panier	59
Avec le panier à ustensiles	59
Panier supérieur	59
Panier inférieur	59
24 cm (9,4 po)	59
34 cm (13,4 po)	59
26,5 cm (10,4 po)	59
30,5 cm (12 po)	59
29 cm (11,4 po)	59
28 cm (11 po)	59
Avec le troisième panier	59
Panier supérieur	59
Panier inférieur	59
18 cm (7 po)	59
34 cm (13,4 po)	59
20,5 cm (8 po)	59
30,5 cm (12 po)	59
23 cm (9 po)	59
28 cm (11 po)	59
RackMatic®	59
1. Faites sortir le panier supérieur du lave-vaisselle jusqu'à la butée.	59
2. Pour abaisser le panier, poussez le levier RackMatic® lever vers l'intérieur.	59
3. Pour relever le panier, tenez les côtés du panier supérieur et soulevez-le.	59
Remarque :	59
Accessoires de panier	60
Peignes rabattables	60
3ème panier	60
Étagère pour tasses	60
Retirer/installer le troisième panier	61
Retirer le troisième panier 1*	61
1. Sortez le troisième panier jusqu'au bout (1).	61
2. Soulevez les galets supérieurs au-dessus des crochets de butée des deux glissières (2).	61
3. Sortez le troisième panier vers l'avant et vers le haut, de sorte que les coins de retenue et les galets inférieurs du panier passent au-dessus des crochets de butée des deux glissières (3).	61
Installer le troisième panier 1*	61
1. Sortez les glissières du troisième panier jusqu'au bout (1).	61
2. Insérez le troisième panier incliné. Assurez-vous que les crochets de butée des deux glissières coulissent entre les coins de retenue et les galets inférieurs du troisième panier (2).	61
3. Glissez le troisième panier à l'intérieur et soulevez les galets supérieurs au-dessus des crochets de butée avant des deux glissières (3).	61
4. Insérez le troisième panier en le poussant (4).	61
Retirer/installer le panier supérieur avec Rackmatic®	62
Retirer le panier supérieur 12	62
1. Sortez le panier supérieur jusqu'au bout (1).	62
2. Soulevez les galets avant sur le crochet de butée de la glissière (2).	62
3. Sortez le panier supérieur vers l'avant et vers le haut, de sorte que les galets supérieurs et inférieurs du panier coulissent au-dessus des crochets de butée des deux glissières (3).	62
Installer le panier supérieur 12	62
1. Sortez les glissières du panier supérieur jusqu'au bout (1).	62
2. Insérez le panier supérieur incliné. Assurez-vous que les crochets de butée des deux glissières coulissent entre les galets supérieurs et inférieurs sur le côté arrière du panier (2).	62
3. Glissez le panier supérieur à l'intérieur et soulevez les galets supérieurs au-dessus des crochets de butée avant des deux glissières (3).	62
4. Insérez le panier supérieur en le poussant (4).	62
. Détergent	63
Détergent	63
AVIS	63
Remarque :	63
Cycle de nettoyage	63
Eau dure/ Souillure importante	63
Eau à dureté moyenne/ Souillure moyenne	63
Eau douce/ Souillure légère	63
Ajout de détergent	64
1. Si le distributeur de détergent 92 demeure fermé, actionnez la barre de verrouillage 9: pour l'ouvrir.	64

Match case Limit results 1 per page

Operating the Dishwasher

en-us

Delay Start

You can delay the start of the cycle in

one hour increments up to 24 hours.

To set Delay start:

Open the door and press the

On/Off

button

(

. Select a cycle.

Press the

Delay

button from the

wash cycle options

until the

displayed time corresponds with

your requirements.

Press the

Start

button

activate Delay start.

To cancel Delay start:

Open the door and press the

Delay

button until

‹‹

indicated on the digital

display

Press the

Start

button

save setting.

Note:

Your dishwasher is protected

against unintentional operation. If the

appliance door remains open for

more than 4 seconds after pressing

the Start button, the operation will be

paused. Press the Start button again

and close the appliance door.

Wash cycle end

The wash cycle has ended when the

display

reads

‹

‹‹

If the signal tone has been set, the

wash cylce end is also indicated by a

buzzer.

To change the signal volume:

Open the door.

Press the

On/Off

button

(

Hold down function key

and

press

Start

button

until the

display

indicates

‹

x (x can

be any number). Release both

buttons.

Press function key

until the

display shows

›

‹ƒ

Press function key

. Each time

the button is pressed the set

value increases by one level;

when it reaches the value

›

‹„

the display jumps back to

›

‹‹

(off).

Press

Start

button

to save

the setting.

Auto power off

This setting determines the length of

time the control panel stays

illuminated after the cycle is

complete. To save energy the

recommended setting is

‹‚

This setting can be adjusted from

‹‹

‹ƒ

To change the setting:

Press the

On/Off

button

(

Hold down the function key

and press the

Start

button

until the display

indicates

‹

x (x can be any number).

Release both buttons.

Press the function key

until

the display

indicates

‹

Press the function key

until

the display corresponds with your

requirements.

Press the

Start

button

‹‚

1 hour delay

ƒ…

24 hours delay

›

‹‹

Off

›

‹‚

low

›

‹ƒ

medium

›

‹„

loud

‹‹

dishwasher does not turn off

automatically

‹‚

dishwasher turns off

automatically after 1 minute

‹ƒ

dishwasher turns off

automatically after

120 minutes (2 hours)