Brother International MFC-P2000 Quick Setup Guide - English - Page 20

Other Control Features - problem

Get Brother International MFC-P2000 - B/W Laser Printer PDF manuals and user guides
UPC - 012502525394
View all Brother International MFC-P2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Other Control Features Sleep Mode When the machine does not receive data for a certain period of time (time-out), it enters sleep mode. Sleep mode acts as though the machine was turned off. The default timeout is 5 minutes. While the machine is in sleep mode, all the lamps are off and it is as if it was turned off, but the machine can still receive data from the computer. Receiving a print file or document automatically wakes up the machine to start printing. Pressing the switch also wakes up the machine.  Note  When the machine goes into sleep mode, the fan will not stop until the print engine has cooled down.  Sleep mode allows the print engine to cool, so the temperature of your room and how long the machine has been in sleep mode affects the warm-up time. This warm-up time can take up to 30 seconds. The Ready lamp blinks to indicate that the machine is warming up.  You can change the timeout for sleep mode with the supplied machine driver or Remote Printer Console program . Refer to the Help section in the printer driver or RPC program for more information about the sleep mode setting. Test Print Mode The machine has the following test print mode. Follow these steps: 1. Make sure that the top cover is closed. 2. Hold down the switch and turn on the power switch. Keep the switch depressed until the Drum lamp comes on. The Drum lamp lights to indicate that the machine is in the test print mode. 3. Press the switch again to execute the test print or hold down the switch to select another option and release the switch to execute the selected option. The test print modes are as follows: Lamp Lit Choice Function Drum Test sample The machine prints a test sample page. page The machine returns to the ready status after printing. Alarm Print Config The machine prints the current configuration of the & Print Fonts I machine and a list of the internal fonts. The machine returns to the ready status after printing. Ready Factory Reset The machine is restored to the factory setting and permanent fonts and macros are cleared. The machine returns to the ready status after printing. Data Hex Dump The machine can print data as hexadecimal values, so that Print you can check data errors and problems. To exit from this mode, you have to turn off the machine. - 18 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
- 18 -
Other Control Features
Sleep Mode
When the machine does not receive data for a certain period of time (time-out), it enters
sleep mode. Sleep mode acts as though the machine was turned off. The default time-
out is 5 minutes. While the machine is in sleep mode, all the
lamps
are off and it is as
if it was turned off, but the machine can still receive data from the computer. Receiving
a print file or document automatically wakes up the machine to start printing. Pressing
the
switch
also wakes up the machine.
Note
±²
When the machine goes into sleep mode, the fan will not stop until the print engine
has cooled down.
±²
Sleep mode allows the print engine to cool, so the temperature of your room and how
long the machine has been in sleep mode affects the warm-up time. This warm-up
time can take up to 30 seconds. The
Ready
lamp blinks to indicate that the machine
is warming up.
±²
You can change the timeout for sleep mode with the supplied machine driver or
Remote Printer Console program . Refer to the Help section in the printer driver or
RPC program for more information about the sleep mode setting.
Test Print Mode
The machine has the following test print mode. Follow these steps:
1.
Make sure that the top cover is closed.
2.
Hold down the switch and turn on the
power
switch. Keep the switch depressed
until the
Drum
lamp comes on.
The
Drum
lamp lights to indicate that the machine is in the test print mode.
3.
Press the switch again to execute the test print or hold down the switch to select
another option and release the switch to execute the selected option.
The test print modes are as follows:
Lamp Lit
Choice
Function
Drum
Test sample
page
The machine prints a test sample page.
The machine returns to the ready status after printing.
Alarm
Print Config
& Print Fonts I
The machine prints the current configuration of the
machine and a list of the internal fonts.
The machine returns to the ready status after printing.
Ready
Factory Reset
The machine is restored to the factory setting and
permanent fonts and macros are cleared.
The machine returns to the ready status after printing.
Data
Hex Dump
Print
The machine can print data as hexadecimal values, so that
you can check data errors and problems. To exit from this
mode, you have to turn off the machine.