Brother International PC-6000 Users Manual - English - Page 49

Brother International PC-6000 Manual

Get Brother International PC-6000 PDF manuals and user guides View all Brother International PC-6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

7. Make a cut of about 2 cm (13/16") in the fabric. O 2 cm (13/16") 0 6 1- N N N N N N )4)?()4 8. Place the fabric as shown left figure B. -Right side of cut: on top of the guide plate -Left side of cut: underneath of the presser foot Guide plate (lower knife) 41) Presser foot 9. Thread the needle, and then pull out a long section of the upper thread, pass it below the presser foot and pull it out in the fabric feed direction. (See left figure B) 41) Presser foot Upper thread 10. Lower the presser foot lever. CAUTION If the width has been adjusted, turn the balance wheel by hand to check that the needle does not touch the side cutter. If the needle touches the side cutter, it may cause the needle to break. When sewing straight stitches only The seam margin should be about 0.5 cm (13/64"). Seam margin Make sure that you touch the " Fstri " key when using the side cutter. Clean the side cutter after use, otherwise dust and scraps of thread will build up on it. Add a small amount of oil as required to the cutting edge of the cutter. Note The fabric will not be cut if the whole fabric is simply spread out underneath the presser foot guide plate. Set the fabric as explained in step 8. above, and start sewing. - Check that the needle is raised when the presser foot lever is raised. - One layer of 13-oz denim can be cut. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
7.
Make
a
cut
of
about
2
cm
(13/16")
in
the
fabric.
O
2
cm
(13/16")
8.
Place
the
fabric
as
shown
left
figure
B.
—
Right
side
of
cut:
on
top
of
the
guide plate
—
Left
side
of
cut:
underneath
of
the
presser
foot
Guide
plate
(lower
knife)
41)
Presser
foot
0
6
1
-
N
N
N
N
N
N
9.
Thread
the
needle,
and
then
pull
out
a
long
sec-
tion
of
the
upper
thread,
pass
it
below
the
presser
foot
and
pull
it
out
in
the
fabric
feed
di-
rection.
(See
left
figure
B)
41)
Presser
foot
Upper
thread
10.
Lower
the
presser
foot
lever.
CAUTION
If
the
width
has
been
adjusted,
turn
the
balance
wheel
by
hand
to
check
that
the
needle
does
not
touch
the
side
cutter.
If
the
needle
touches
the
side
cutter,
it
may
cause
the
needle
to
break.
When
sewing
straight
stitches
only
The
seam
margin
should
be
about
0.5
cm
(13/64").
Seam
margin
Make
sure
that
you
touch
the
"
Fstri
"
key
when
using
the
side
cutter.
Clean
the
side
cutter
after
use,
otherwise
dust
and
scraps
of
thread
will
build
up
on
it.
Add
a
small
amount
of
oil
as
required
to
the
cutting
edge
of
the
cutter.
Note
The
fabric
will
not
be
cut
if
the
whole
fabric
is
simply
spread
out
underneath
the
presser
foot
guide
plate.
Set
the
fabric
as
explained
in
step
8.
above,
and
start
sewing.
-
Check
that
the
needle
is
raised
when
the
presser
foot
lever
is
raised.
-
One
layer
of
13
-oz
denim
can
be
cut.
45