Brother International SB3734T Operation Manual - Page 8

Powering the machine, Turning direction of hand wheel, Opening/ Closing front cover, Attaching/

Get Brother International SB3734T PDF manuals and user guides View all Brother International SB3734T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Powering the machine Turning on the machine 1. Insert the three-pin plug into the socket on the bottom right side of the machine. Insert the power supply plug into a power outlet. 2. Turn the main power and light switch to "I" mark (to "O" mark to turn off). Opening/ Closing front cover It is necessary to open the front cover when threading this machine. Slide it to the right 1 and open 2, or close it and slide it to the left. CAUTION For your safety, make sure that the front cover is closed when operating the machine. Always turn off the machine before opening the front cover. Operation When the foot controller is pressed lightly, the machine runs at a low speed. As the foot controller is pressed further, the machine will increase speed. When the foot controller is released, the machine stops. NOTE (For U.S.A. only): Foot controller: Model KD-1902 This foot controller can be used on the machine with product code 884-B02 and 884-B03. * The product code is shown on the machine rating plate. Turning direction of hand wheel The hand wheel turns in a counterclockwise direction (direction of arrow). This is the same direction as an ordinary home sewing machine. The needles move to their highest positions by turning the hand wheel so that the mark on the hand wheel is aligned to the line on the machine. 1 2 Attaching/ Removing presser foot 1. Turn off the main power and light switch or disconnect the electric supply plug. 2. Raise the presser foot lever. 1 3. Turn the hand wheel 2 so that the mark on the hand wheel is aligned to the line on the machine. (See CHAPTER1 "Turning direction of hand wheel".) 4. Push the button on the presser foot holder and the standard presser foot will be released. 3 4 5. Raise the presser foot farther by pushing the presser foot lever upward. Then remove the presser foot and store it in a safe location. 6. Again, raise the presser foot farther by pushing the presser foot lever upward. Then place the presser foot just under the presser foot holder so that the groove in the bottom of the presser foot holder is aligned and catches the bar on the top of the foot . Then lower the presser foot lever to attatch the foot, pushing the button on the presser foot. 6 4 12 1 3 2 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
6
Powering the machine
Turning on the machine
1. Insert the three-pin plug into the socket on the
bottom right side of the machine. Insert the
power supply plug into a power outlet.
2. Turn the main power and light switch <A> to "I"
mark (to "O" mark to turn off).
<A>
Operation
When the foot controller is pressed lightly, the
machine runs at a low speed. As the foot controller
is pressed further, the machine will increase
speed. When the foot controller is released, the
machine stops.
NOTE (For U.S.A. only):
Foot controller: Model KD-1902
This foot controller can be used on the machine
with product code 884-B02 and 884-B03.
* The product code is shown on the machine rating
plate.
Turning direction of hand wheel
The hand wheel <A> turns in a counterclockwise
direction (direction of arrow). This is the same
direction as an ordinary home sewing machine.
The needles move to their highest positions by
turning the hand wheel so that the mark <B>
on the hand wheel is aligned to the line on the
machine.
<A>
<B>
Opening/ Closing front cover
It is necessary to open the front cover when
threading this machine. Slide it to the right
1
and
open
2
, or close it and slide it to the left.
CAUTION
For your safety, make sure that the front cover is
closed when operating the machine.
Always turn off the machine before opening the
front cover.
1
2
Attaching/ Removing presser foot
1. Turn off the main power and light switch or
disconnect the electric supply plug.
2. Raise the presser foot lever.
1
3. Turn the hand wheel
2
so that the mark on
the hand wheel is aligned to the line on the
machine. (See CHAPTER1 "Turning direction
of hand wheel".)
4.
Push the button on the presser foot holder and
the standard presser foot will be released.
3 4
5. Raise the presser foot farther by pushing the
presser foot lever upward. Then remove the
presser foot and store it in a safe location.
6. Again, raise the presser foot farther by pushing
the presser foot lever upward. Then place the
presser foot just under the presser foot holder
<A> so that the groove in the bottom of the
presser foot holder <B> is aligned and catches
the bar on the top of the foot <C>. Then lower
the presser foot lever to attatch the foot,
pushing the button on the presser foot.
<A>
<C>
<B>
1
1
2
3
2
4
4