Canon Color imageCLASS LBP712Cdn imageCLASS LBP712Cdn Getting Starte - Page 14

Important Safety Instructions • Remove the power plug completely from the conditions: (1) This device may not cause harmful AC power outlet during a thunder storm. interference, and (2) this device must accept any This manual describes only warnings and cautions for the installation and the power supply. Be sure Failure to do so may result in a fire, electrical shock, or damage to the machine. interference received, including interference that may cause undesired operation. to read "Important Safety Instructions" described in the e-Manual (HTML manual) also. WARNING Indicates a warning concerning operations that may lead to death or injury to persons if CAUTION Install this machine near the power outlet and leave sufficient space around the power plug so that it can be unplugged easily in an emergency. Handling FCC CAUTION [NOTE] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection not performed correctly. To use the machine safely, always pay attention to these warnings. CAUTION Indicates a caution concerning operations that may lead to injury to persons if not performed correctly. To use the machine safely, always pay attention to these cautions. Installation WARNING Do not install in a location that may result in a Laser Safety This product is confirmed as a Class 1 laser product in IEC60825-1:2007 and EN60825-1:2007. CLASS 1 LASER PRODUCT LASER KLASSE 1 APPAREIL À LASER DE CLASSE 1 APPARECCHIO LASER DI CLASSE 1 PRODUCTO LÁSER DE CLASE 1 APARELHO A LASER DE CLASSE 1 LUOKAN 1 LASER-TUOTE LASERPRODUKT KLASS 1 against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by fire or electrical shock The laser beam can be harmful to human bodies. one or more of the following measures: • A location where the ventilation slots are blocked (too close to walls, beds, sofas, rugs, or similar objects) • A damp or dusty location • A location exposed to direct sunlight or outdoors • A location subject to high temperatures • A location exposed to open flames • Near alcohol, paint thinners or other flammable substances Other warnings • Do not connect unapproved cables to this machine. Doing so may result in a fire or electrical shock. • Do not place necklaces and other metal objects or containers filled with liquid on the machine. If foreign substances come in contact with electrical parts inside the machine, it may result in a fire or electrical shock. • If any foreign substance falls into this machine, Since radiation emitted inside the product is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation. Read the following remarks and instructions for safety. • Never open covers other than those instructed in the manuals for this machine. • If the laser beam should escape and enter your eyes, exposure may cause damage to your eyes. CAUTION Use of controls, adjustments, or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. Safety-Related Symbols Power switch: "ON" position Power switch: "OFF" position - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in this manual. If you make such changes or modifications, you could be required to stop operation of the equipment. CANON U.S.A., INC One Canon Park, Melville, NY 11747, U.S.A. TEL No. 1-800-OK-CANON unplug the power plug from the AC power outlet Power switch: "STAND‐BY" position Disclaimers and contact your local authorized Canon dealer. CAUTION Do not install in the following locations The machine may drop or fall, resulting in injury. • An unstable location • A location exposed to vibrations Other cautions • When carrying this machine, follow the instructions in this manual. If carried improperly, it may fall, resulting in injury. • When installing this machine, be careful not to get your hands caught between the machine and the floor or walls. Doing so may result in injury. Push‐push switch "ON" "OFF" Protective earthing terminal Dangerous voltage inside. Do not open covers other than instructed. CAUTION: Hot surface. Do not touch. Class II equipment Moving parts: Keep body parts away from moving parts [NOTE] Some of symbols shown above may not be affixed depending on the product. v1511_02_en-GB • The following applies in California, USA only: The battery included with your product contains Perchlorate Material and may require special handling. See http://www.dtsc.ca.gov/hazardouswaste/ perchlorate/ for details. Trademarks Mac is a trademark of Apple Inc. Microsoft, Windows, Windows Vista, Windows Server, Internet Explorer, Excel, and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and/ or other countries. Other product and company names herein may Avoid poorly ventilated locations This machine generates a slight amount of ozone Laser Safety Label and other emissions during normal use. These emissions are not harmful to health. However, they may be noticeable during extended use or long production runs in poorly ventilated rooms. En To maintain a comfortable working environment, it is recommended that the room where the machine operates be appropriately ventilated. Also avoid locations where people would be exposed to emissions from the machine. be the trademarks of their respective owners. Third-Party Services If you use third-party services through the PRODUCT, use of the services are subjected the conditions below. When you access and/or obtain some third party content (such as text, images, videos, audios, or software) through the SOFTWARE, except as expressly permitted by the content owner or by applicable law, you may not (a) scrape, build databases or otherwise create permanent copies Power Supply of such content, or keep cached copies longer WARNING • Use only a power supply that meets the specified voltage requirements. Failure to do so may result in a fire or electrical shock. • Do not use power cords other than the one provided, as this may result in a fire or electrical shock. • The provided power cord is intended for use with this machine. Do not connect the power cord to other devices. Consumables WARNING Do not dispose of used toner cartridges or the like in open flames. Also, do not store toner cartridges or paper in a location exposed to open flames. This may cause the toner to ignite, and result in burns or fire. than permitted by the cache header; (b) copy, translate, modify, create a derivative work of, sell, lease, lend, convey, distribute, publicly display or sublicense to any third party; (c) misrepresent the source or ownership; and (d) remove, obscure, or alter any copyright, trademark or other proprietary rights notices, falsify or delete any author attributions, legal notices or other labels of the origin or source of material. • Do not modify, pull, forcibly bend, or perform any other act that may damage the power cord. Do not place heavy objects on the power cord. Damaging the power cord may result in a fire or electrical shock. • Do not plug in or unplug the power plug with wet hands, as this may result in an electrical shock. • Do not use extension cords or multi-plug power strips with the machine. Doing so may result in a fire or electrical shock. • Do not wrap the power cord or tie it in a knot, as this may result in a fire or electrical shock. • Insert the power plug completely into the AC power outlet. Failure to do so may result in a fire or electrical shock. Notice Product Name Safety regulations require the product's name to be registered. In some regions where this product is sold, the following name(s) in parentheses ( ) may be registered instead. Color imageCLASS LBP712Cdn (F169200) FCC (Federal Communications Commission) Users in the U.S.A. Laser Beam Printer, Model F169200 This device complies with part 15 of the FCC Rules. Operation is subject to the following two Third Party Software This Canon product (the "PRODUCT") includes third-party software modules. Use and distribution of these software modules, including any updates of such software modules (collectively,the "SOFTWARE") are subject to license conditions below. (1) You agree that you will comply with any applicable export control laws, restrictions or regulations of the countries involved in the event that the PRODUCT including the SOFTWARE is shipped, transferred or exported into any country. 14