Canon imageCLASS MF3110 Service Manual - Page 67
Removing the Power, Supply Shield Plate, Supply Assembly, Removing the Top, Sensor
View all Canon imageCLASS MF3110 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 67 highlights
3.1.11.11 Removing the Power Supply Shield Plate 0007-7547 1) Remove the 5 screws [1] to remove the power supply shield plate [2]. [2] Chapter 3 3) As you remove the bosses on both sides [1], lower the front part of the power supply assembly [2]. Then pull it to remove the power supply assembly. [2] [1] [1] F-3-75 3.1.11.12 Removing the Power Supply Assembly 0007-7550 1) Remove the 3 screws [1]. 2) Remove the 4 connectors [2] as well as the flat cable [3] on the ECNT board. [1] F-3-77 3.1.11.13 Removing the Top Sensor 0007-7552 1) Place the main unit down on its front face (so that the interior of the main unit is easily visible). 2) Remove the connector [1] on the ECNT board and take the cable off the cable guide. 3) Remove the screw [2] and remove the top sensor [3]. [2] [1] [2] F-3-76 [3] [2] [1] F-3-78 [3] [1] 3-19
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176