Canon imageCLASS MF3110 Service Manual - Page 89
Removing the Power, Supply Shield Plate, Supply Assembly, Removing the Gear
View all Canon imageCLASS MF3110 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 89 highlights
3.5.1.11 Removing the Power Supply Shield Plate 0007-7813 1) Remove the 5 screws [1] to remove the power supply shield plate [2]. [2] Chapter 3 3) As you remove the bosses on both sides [1], lower the front part of the power supply assembly [2]. Then pull it to remove the power supply assembly. [2] [1] [1] F-3-158 3.5.1.12 Removing the Power Supply Assembly 0007-7816 1) Remove the 3 screws [1]. 2) Remove the 4 connectors [2] as well as the flat cable [3] on the ECNT board. [1] F-3-160 3.5.1.13 Removing the Gear Unit 0007-7818 1) Remove the 2 screws [1], and detach the drive plate (small) [2]. [2] [1] [2] F-3-159 [3] [2] [1] [1] F-3-161 2) Remove the 2 gears [1]. 3) While freeing the claw, detach the gear unit [2]. [2] [1] F-3-162 3-41
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
Chapter 3
3-41
3.5.1.11
Removing the Power
Supply Shield Plate
0007-7813
1) Remove the 5 screws [1] to remove the power
supply shield plate [2].
F-3-158
3.5.1.12
Removing the Power
Supply Assembly
0007-7816
1) Remove the 3 screws [1].
2) Remove the 4 connectors [2] as well as the flat
cable [3] on the ECNT board.
F-3-159
3) As you remove the bosses on both sides [1], lower
the front part of the power supply assembly [2].
Then pull it to remove the power supply assembly.
F-3-160
3.5.1.13
Removing the Gear
Unit
0007-7818
1) Remove the 2 screws [1], and detach the drive plate
(small) [2].
F-3-161
2) Remove the 2 gears [1].
3) While freeing the claw, detach the gear unit [2].
F-3-162
[1]
[1]
[2]
[1]
[2]
[2]
[1]
[3]
[1]
[2]
[2]
[1]
[2]
[1]