Canon imageRUNNER 1025 Series Quick Start Guide - Page 17

Register User Telephone Number and Unit Name, Information About the Keys

Get Canon imageRUNNER 1025 PDF manuals and user guides View all Canon imageRUNNER 1025 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3 Make Fax Settings (imageRUNNER 1025iF Only) Register User Telephone Number and Unit Name This section describes the procedure for registering the user telephone number and unit name. For instructions for entering information, refer to "Information About the Keys" below. Information About the Keys Use the keys shown below to enter information in the machine. You can enter the following characters in each input mode: ● Use - [numeric keys] to enter characters. Press - [numeric keys] repeatedly until the required character appears. ● Press to enter symbols. ● Press to switch between input modes: : Letter mode : Number mode ● Press [ ] or [ ] to move the cursor position. ● Press [Clear] to delete the character at the cursor position. Press and hold [Clear] to delete the entire entry. ● Press [OK] to set the entry and to proceed to the next screen. ● The display returns to the standby mode: The machine may enter the standby mode (Auto Clear function) while you are setting it up. Make the setting again from the main menu. ● The display turned off: The machine may enter the sleep mode while you are setting it up. Press [Power] to turn the machine back ON and continue the setup. 1 Press [Additional Functions]. 2 Press [ ] or [ ] to select , then press [OK]. ADD.FUNCTIONS 3.TX/RX SETTINGS 3 Press [ ] or [ ] to select , then press [OK]. TX/RX SETTINGS 2.FAX SETTINGS 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
15
3 Make Fax Settings (imageRUNNER 1025iF Only)
Use the keys shown below to enter information in the machine.
You can enter the following characters in each input mode:
Use
–
[numeric keys] to enter characters.
Press
–
[numeric keys] repeatedly until the
required character appears.
Press
to enter symbols.
Press
to switch between input modes:
<:a>: Letter mode
<:1>: Number mode
Press [
] or [
] to move the cursor
position.
Press
[Clear] to delete the character at the
cursor position. Press and hold
[Clear] to
delete the entire entry.
Press [
OK
] to set the entry and to proceed to
the next screen.
●
●
●
●
●
●
Register User Telephone Number and Unit Name
This section describes the procedure for registering the user telephone number and unit name. For instructions
for entering information, refer to “Information About the Keys” below.
Information About the Keys
The display returns to the standby mode:
The machine may enter the standby mode (Auto Clear function) while you are
setting it up. Make the setting again from the main menu.
The display turned off:
The machine may enter the sleep mode while you are setting it up. Press
[Power] to turn the machine back ON and continue the setup.
1
Press
[Additional Functions].
●
●
2
Press [
] or [
] to select <3. TX/RX
SETTINGS>, then press [
OK
].
3.TX/RX SETTINGS
ADD.
FUNCTIONS
3
Press [
] or [
] to select <2. FAX SETTINGS>,
then press [
OK
].
2.FAX SETTINGS
TX/RX SETTINGS