Home » Cisco Manuals » Bridges & Routers » Cisco 7206VXR » Manual Viewer

Cisco 7206VXR Hardware Guide - Page 33

Error Messages - 300

UPC - 746320975061

Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 1 Cisco 7200 Series Port Adapter Installation Requirements Error Messages Error Messages The system prompts you with error messages if your port adapter configuration exceeds the guidelines in this document. Following are examples of the error messages: • For a Cisco 7200 series router or Cisco 7200 VXR router that has an NPE-225, NPE-200, NPE-175, NPE-150, or NPE-100 installed, the following error messages are displayed when the bandwidth points exceed the system limit: %C7200-3-PACONFIG:Exceeds 3 high speed port adapters %C7200-3-PACONFIG:Exceeds 5 high/medium speed port adapters %C7200-3-PACONFIG:Exceeds 800 aggregate port adapter bandwidth points • For a Cisco 7200 VXR router that has an NPE-400, NPE-300, or NSE-1 installed, the following error messages are displayed when the bandwidth points are exceeded on the buses: %C7200-3-PACONFIG:Exceeds 600 bandwidth points for slots 0, 1, 3 & 5 %C7200-3-PACONFIG:Exceeds 600 bandwidth points for slots 2, 4 & 6 %C7200-3-PACONFIG:Exceeds 600 bandwidth points on both odd & even numbered slots OL-3875-11 Cisco 7200 Series Port Adapter Hardware Configuration Guidelines 1-25

Section	Page
Cisco 7200 Series Port Adapter Hardware Configuration Guidelines	1
Contents	3
Preface	5
Document Revision History	5
Introduction	5
Other Documentation	6
Obtaining Documentation, Obtaining Support, and Security Guidelines	7
Cisco 7200 Series Port Adapter Installation Requirements	9
Chassis Overview—Front View	10
Chassis Overview—Rear View	11
Configuration Guidelines and Requirements	12
PCI Buses and Port Adapter and I/O Controller Architecture	12
Port Adapter Slot Numbering	13
Guidelines for Installation	14
Installation Requirements Based on the NPE or NSE Installed	16
NPE-G1 or NPE-G2 Bandwidth Calculation and Configuration Instructions	16
Sample Bandwidth Configuration for the NPE-G1 or NPE-G2	17
NPE-G1 or NPE-G2 with a Port Adapter Jacket Card—Bandwidth Calculation and Configuration Instruct...	17
NPE-400, NPE-300, and NSE-1 Bandwidth Calculation and Configuration Instructions	17
Sample Bandwidth Configuration for the NPE-400, NPE-300, and NSE-1	18
NPE-225, NPE-200, NPE-175, NPE-150, and NPE-100 Bandwidth Calculation and Configuration Instructions	19
Sample Bandwidth Configuration for the NPE-225, NPE-200, NPE-175, and NPE-150	20
Bandwidth and Bandwidth Point Requirements	21
Requirements Summary	21
Port Adapter Jacket Card	21
NPE-G1 or NPE-G2	21
NPE-400, NPE-300, NSE-1	21
NPE-225, NPE-200, NPE-175, NPE-150	22
NPE-100	22
Bandwidth Table	22
Bandwidth Calculation Table	30
Messages for One Port Use of Specific Port Adapters and an I/O Controller	30
NPE-400	31
NPE-G1 or NPE-G2	32
Error Messages	33
Memory Requirements	35
Determining Port Adapter and System Memory Requirements	36
Sample Configuration Showing Processor Memory Required	36
Cisco IOS Software Memory Requirements	38
Determining DRAM or SDRAM Required If the Router Has Only 32 MB of Memory (NPE-100, NPE-150, and ...	39

Match case Limit results 1 per page

1-25

Cisco 7200 Series Port Adapter Hardware Configuration Guidelines

OL-3875-11

Chapter 1

Cisco 7200 Series Port Adapter Installation Requirements

Error Messages

The system prompts you with error messages if your port adapter configuration exceeds the guidelines

in this document. Following are examples of the error messages:

•

For a Cisco 7200 series router or Cisco 7200 VXR router that has an NPE-225, NPE-200, NPE-175,

NPE-150, or NPE-100 installed, the following error messages are displayed when the bandwidth

points exceed the system limit:

%C7200-3-PACONFIG:Exceeds 3 high speed port adapters

%C7200-3-PACONFIG:Exceeds 5 high/medium speed port adapters

%C7200-3-PACONFIG:Exceeds 800 aggregate port adapter bandwidth points

•

For a Cisco 7200 VXR router that has an NPE-400, NPE-300, or NSE-1 installed, the following

error messages are displayed when the bandwidth points are exceeded on the buses:

%C7200-3-PACONFIG:Exceeds 600 bandwidth points for slots 0, 1, 3 & 5

%C7200-3-PACONFIG:Exceeds 600 bandwidth points for slots 2, 4 & 6

%C7200-3-PACONFIG:Exceeds 600 bandwidth points on both odd & even numbered slots