Cisco AIR-CB21AG-W-K9 Configuration Guide - Page 27

Bottom of Antenna Base, Step 1

Get Cisco AIR-CB21AG-W-K9 PDF manuals and user guides View all Cisco AIR-CB21AG-W-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 1 Product Overview and Installation Inserting the Client Adapter Follow the steps below to position the PCI card's antenna on a flat horizontal surface or to mount it to a wall. Step 1 Step 2 Perform one of the following: • If you want to use the antenna on a flat horizontal surface, position the antenna so it is pointing straight up. Then go to Step 7. • If you want to mount the antenna to a wall, go to Step 2. Drill two holes in the wall that are 1.09 in. (2.8 cm) apart. Figure 1-7 shows the distance between the mounting holes on the bottom of the antenna base. Figure 1-7 Bottom of Antenna Base 1.09 inches 95597 Step 3 Step 4 Step 5 Tap the two supplied wall anchors into the holes. Drive the two supplied screws into the wall anchors, leaving a small gap between the screw head and the anchor. Position the mounting holes on the bottom of the antenna base over the screws (see Figure 1-8) and pull down to lock in place. Cisco Aironet 802.11a/b/g Wireless LAN Client Adapters (CB21AG and PI21AG) Installation and Configuration Guide for Windows Vista OL-16534-01 1-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
1-15
Cisco Aironet 802.11a/b/g Wireless LAN Client Adapters (CB21AG and PI21AG) Installation and Configuration Guide for Windows Vista
OL-16534-01
Chapter 1
Product Overview and Installation
Inserting the Client Adapter
Follow the steps below to position the PCI card’s antenna on a flat horizontal surface or to mount it to a
wall.
Step 1
Perform one of the following:
•
If you want to use the antenna on a flat horizontal surface, position the antenna so it is pointing
straight up. Then go to Step 7.
•
If you want to mount the antenna to a wall, go to Step 2.
Step 2
Drill two holes in the wall that are 1.09 in. (2.8 cm) apart.
Figure 1-7
shows the distance between the
mounting holes on the bottom of the antenna base.
Figure 1-7
Bottom of Antenna Base
Step 3
Tap the two supplied wall anchors into the holes.
Step 4
Drive the two supplied screws into the wall anchors, leaving a small gap between the screw head and the
anchor.
Step 5
Position the mounting holes on the bottom of the antenna base over the screws (see
Figure 1-8
) and pull
down to lock in place.
95597
1.09 inches