Cisco ASR1004-20G-SEC/K9 Software Guide - Page 136
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2), Using ISSU to Upgrade SubPackages (Prior to Cisco IOS XE Release 2.1.2)
View all Cisco ASR1004-20G-SEC/K9 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 136 highlights
ISSU Upgrade for Redundant Platforms Chapter 4 Software Upgrade Process This section contains the following topics: • Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2), page 4-74 • Using ISSU to Upgrade SubPackages (Prior to Cisco IOS XE Release 2.1.2), page 4-74 Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2) This procedure is identical to the procedure used to upgrade post-Cisco IOS XE 2.2 images using ISSU. See the "Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration" section on page 4-5 for instructions on performing this process. Using ISSU to Upgrade SubPackages (Prior to Cisco IOS XE Release 2.1.2) This procedure will work on single RPs configured to run two IOS processes or on routers configured with dual RPs. Versions of Cisco IOS XE Release 2.1 prior to Cisco IOS XE Release 2.1.2 and versions of Cisco IOS XE Release 2.2 prior to Cisco IOS XE Release 2.2.1 and installations not booted from the RPBase subpackage on Cisco IOS XE Release 2.2.1 or 2.1.2 require a different ISSU upgrade procedure. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Copy all subpackages other than the RPBase subpackage into the same directory. Install the RP subpackages from the directory simultaneously by using a wildcard statement to capture all of the RP subpackages. This command should capture the RPControl, RPAccess, and RPIOS subpackages without capturing the RPBase subpackage and should be done using the standby bay. Use the asr1000rp1-rp*version.pkg syntax instead of using the {pattern} syntax to complete this upgrade: request platform software package install rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg bay 1 force Wait for the system to reach SSO ready state. The show platform command can be used to monitor whether both IOS instances are active, and a system message will indicate SSO state has been reached. Use the redundancy force-switchover command to trigger an IOS switchover. Wait for the system to reach SSO ready state. Like in step 3, the state can be monitored by checking system messages or by entering the show platform command. Install the RP subpackages from the directory simultaneously by using a wildcard statement to capture all of the RP subpackages. This command should capture the RPControl, RPAccess, and RPIOS subpackages without capturing the RPBase subpackage and should be done using the standby bay. Use the "asr1000rp1-rp*version.pkg syntax instead of using the {pattern} syntax to complete this upgrade: request platform software package install rp 0 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg bay 0 force Install the SIPBASE and SIPSPA packages on each SIP: Router# request platform software package install rp 0 file bootflash:asr1000rp1-sip*02.02.01.122-33.XNB1*.pkg slot 0 force Router# request platform software package install rp 0 file bootflash:asr1000rp1-sip*02.02.01.122-33.XNB1*.pkg slot 1 force 4-74 Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-10